Troy-Bilt Trimmer Carburetors

Fix Number

FIX9119300

Manufacturer Part Number

753-06190

A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.

Fix Number

FIX19283399

Manufacturer Part Number

753-06288

Fix Number

FIX16428389

Manufacturer Part Number

753-06258A

A carburetor is an important component which combines fuel and air before the combustible mixture is sent into the cylinder. Over time parts may wear out or get damaged eventually requiring a replacement. Keep in mind this high-quality carburetor is sold as an individual item. Refer to the appropriate diagrams for your model to ensure the correct repair procedure. It is a genuine OEM carburetor which is specially made for lawn and garden equipment.

Fix Number

FIX11812945

Manufacturer Part Number

753-08174

This is an original replacement part sourced directly from the manufacturer. The carburetor is found in Craftsman trimmers. This part is a complete carburetor assembly made primarily of metal, and is used to mix fuel and air together for ignition in the engine. You will require a screwdriver when replacing this item. The carburetor is sold as an individual replacement part.

★★★★★

★★★★★

1 Review

Fix Number

FIX9119777

Manufacturer Part Number

753-1225

This is an Genuine OEM replacement part used on Gas-Powered Handheld Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor with Rubber Primer Bulb and Two (2) Rubber Fuel Lines. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.

Fix Number

FIX9119819

Manufacturer Part Number

753-04338

This is an authentic OEM produced replacement carburetor assembly. It is specially made for use on handheld gas powered lawn and garden equipment. It mixes air and gas into a combustible mixture that is sent into the engine. This kit includes (1) metal body carburetor, (1) composite gasket, (3) flexible rubber fuel lines and (1) fuel filter. To replace this carburetor assembly you will need a screwdriver.

Fix Number

FIX9130480

Manufacturer Part Number

753-05251

Carburetor w/Primer Carburetor WYL-229 This carburetor is for line trimmers. Carburetor mixes air and gas before the fuel mix goes to the engine.

Fix Number

FIX9119056

Manufacturer Part Number

753-06288

This carburetor is for line trimmers. Carburetor mixes air and gas before the fuel mix goes to the engine. Wear work gloves to protect your hands and work in a well-ventilated area during this repair.

Fix Number

FIX9118980

Manufacturer Part Number

753-04014

Fix Number

FIX9137106

Manufacturer Part Number

791-182347

This is an OEM part sourced directly from the manufacturer. The carburetor mount is commonly found in trimmers from Ryobi, MTD, Troy-Bilt, Yard Man, and Bolens. This part is made of high-quality plastic, and is used to help connect the carburetor assembly with the cylinder head. You may require a screwdriver when replacing this part. This item is sold individually.