Shindaiwa Leaf Blower / Vacuum Parts
Start With Your Model Number
Popular Shindaiwa Leaf Blower / Vacuum Parts
Fix Number FIX8858167
Manufacturer Part Number 12318140630This is a primer pump or primer bulb, and it is used on various outdoor lawn equipment. This part has an outer diameter of 0.616 inches, it is dome shaped, and transparent. The primer pump gives the engine of your machine a faster start by pulling fuel into the carburetor. If your pump is malfunctioning your machine will not receive the fuel it needs to operate properly. If you notice the primer pump is leaking you must replace it, as it could become dangerous.
Steve from Hilliard, OH
Replaced fuel line, primer,filter and hoesIn home shop Read more...
Fix Number FIX11826309
Manufacturer Part Number A369000460This is an OEM fuel filter and is sold individually. This repair is very easy and will only take a few minutes. It is also a very important maintenance task that should be done regularly. This part is located inside the fuel tank and filters out debris to prevent it from making its way to the carburetor. If you notice fuel is leaking or their seems to be blockage, your fuel filter is likely in need of a replacement.
Fuel Tank Vent
Fix Number FIX9183121
Manufacturer Part Number A356000031This check valve or the fuel tank vent is connected to the fuel tank in the following products: hedge trimmer, leaf blower/vacuum, chainsaw, edger, engine, tiler, auger, water pump, chipper shredder, sprayer, and brush cutter. The check valve allows air into the fuel tank to prevent vacuum when the fuel is being fed through the fuel line. Tip: if the vent is clogged, your engine may stall. Usually, the vent line is connected to a fuel grommet that is installed on the fuel tank. The tools needed for this installation are: needle-nose pliers and a small slotted screwdriver. Remember to wear work gloves to protect hands. Refer to the manual for an accurate repair guide.
Fix Number FIX11826311
Manufacturer Part Number A369000480This is a single OEM fuel filter that has been approved by the manufacturer, ensuring the highest quality. It is compatible with numerous types of outdoor power equipment, such as blowers, trimmers, edgers, chainsaws, etc. This is a very important maintenance part that should be replaced on a regular schedule. Its purpose is to remove contaminants that could clog up the carburetor, which should also be regularly inspected. For this simple repair, slide the new fuel filter onto the fuel line and use a screwdriver to place the clamp tightly over the nipple.
Fix Number FIX10053748
Manufacturer Part Number V490001230This is a clip for a variety of lawn and garden equipment. The clip is made of a durable metal, and is 6.5mm in diameter. This part is most commonly used to clamp tubes and hoses in place. The clip is sold individually.
Fix Number FIX9237390
Manufacturer Part Number V107000010This gasket fits lawn and garden equipment. It provides a seal for the gas cap. With use, the seal can wear off and become compressed. In this case, it is best to replace the gasket. *Please note: this part is sold individually. No tools needed are needed to replace this gasket, simply remove the old one and place a new gasket inside the fuel cap.
Fix Number FIX9238696
Manufacturer Part Number V490000500This clip fits lawn and gardening tools. The clip secures the fuel filter to the fuel line on the unit. *Please note: the clip is sold separately. Refer to the manual provided by the manufacturer for further installation instructions.
Spark Plug Bpm-8Y
Fix Number FIX9263506
Manufacturer Part Number 15901019830Replacing the spark plug should be part of your regular maintenance. How often to replace it depends on your model but is generally changed at least once a year or more, depending on use. When a spark plug has gone bad this can lead to a hard-starting engine, a misfire, or the engine not starting at all. Replacing it is very easy. Start by gapping your new spark plug according to the manufacturer specifications. For this repair, start by removing the boot from the old plug, use a wrench to remove it, and twist it off with your hand. Now thread the new replacement spark plug into place and tighten it using the wrench. This manufacturer-approved spark plug is sold individually.