Craftsman Lawn Tractor Belts

Fix Number

FIX17016841

Manufacturer Part Number

598559101

Belt

★★★★★

★★★★★

1 Review

Fix Number

FIX9186148

Manufacturer Part Number

954-0467A

This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit. Make sure to clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Loosen the transaxle pulley • Relieve tension on the upper drive belt • Remove the upper drive belt and lawn mower belt guide • Secure the new belt • Reassemble and tighten the pulleys

Fix Number

FIX11813755

Manufacturer Part Number

954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Fix Number

FIX9011522

Manufacturer Part Number

532144959

This is a genuine replacement belt sourced directly from the original manufacturer, designed for use with riding lawn tractors and mowers. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a critical component for cutting performance. To ensure optimal function and longevity, it’s important to clean the pulleys before installing the new belt and to inspect the belt regularly for signs of wear or stretching. Replacing the belt requires a wrench set and pliers. For safety, always disconnect the spark plug wire before beginning. Start by lowering the mower deck to its lowest position and setting the blade engagement lever to the "Off" position. Roll the old belt off the engine pulley from between the belt guide and pulley. Remove the mower deck by taking out the bow-tie pins securing the left and right lift arms, then disconnect the blade engagement cable. Next, remove the bolts from the mower deck belt pulley covers and take off the covers. Loosen, but do not remove, the nuts on the top of the idler pulleys. Install the new mower deck belt through the belt guides and around the pulleys, then tighten the idler pulley nuts. Finally, reassemble the deck to complete the repair and restore your mower’s cutting performance. Lawn mower deck belt. Width: 1/2 " Length: 95 1/2 ".

Fix Number

FIX17016487

Manufacturer Part Number

593773401

This is a genuine replacement belt sourced from the original manufacturer, designed for use with riding lawn mowers and tractors. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a key component for effective cutting performance. To ensure optimal operation and extend the life of the belt, it’s important to clean the pulleys before installation. Regular inspection is recommended, and the belt should be replaced if it becomes worn or stretched. A set of wrenches is required to complete the installation.

Fix Number

FIX11965490

Manufacturer Part Number

532125907

This is an OEM drive belt for lawn tractors. It is also commonly referred to as a v-belt or ground belt. It measures approximately 1/2-inch by 90-inches. It turns the transmission pulley to move the lawn tractor. If the lawn tractor is not moving, is moving sluggishly or the wheels are not turning, it is likely due to a broken or worn drive belt. Please note this belt is sold individually and you may require a 5/8-ich socket and pipe wrench for the repair

Fix Number

FIX17016497

Manufacturer Part Number

531169501

Belt Keeper

Fix Number

FIX9011141

Manufacturer Part Number

532140294

Fix Number

FIX10035504

Manufacturer Part Number

954-05040

Fix Number

FIX17016498

Manufacturer Part Number

531169701

This is a genuine replacement part sourced from the original manufacturer, designed for use with riding mowers and tractors made by Weedeater, Husqvarna, Jonsered, and Poulan. Made of durable metal, this component functions as a belt guide, helping to maintain the correct path of the belt between pulleys for smooth and efficient operation. It is sold individually and is essential for proper belt alignment and performance. To replace this part, you will need an adjustable wrench. Always consult your equipment’s manual for proper installation and compatibility.