Little Wonder Edger Parts
Start With Your Model Number
Find Parts Fast Guaranteed Fit Repair VideosNeed help finding your model number?
Popular Little Wonder Edger Parts
Fix Number FIX11826164
Manufacturer Part Number 90152YIn order to keep your equipment running strong, doing regular maintenance is critical. Your small engine should have a tune-up once per year, which consists of replacing the most common wear parts. This OEM-sourced kit includes an air filter; spark plug and fuel filter. Replacing all the parts in this kit should not take any longer than five minutes. Start by installing the air filter. Remove the air filter cover and air filter. Place the new air filter on the filter case and place the cover back on. Next, replace the fuel filter. Remove the gas cap and use a wire hook to lift the fuel line from the tank. Remove the old filter and line up the new one onto the fuel line, making sure the retaining clamp fits over the nipple. Lastly, replace the spark plug by first removing the boot. Use a wrench to remove the spark plug. Before installing the new spark plug be sure to check the gap between the electrodes. Install the new spark plug into the cylinder and place the boot back on.
Fix Number FIX11826485
Manufacturer Part Number P005003120
Fix Number FIX11826311
Manufacturer Part Number A369000480This is a single OEM fuel filter that has been approved by the manufacturer, ensuring the highest quality. It is compatible with numerous types of outdoor power equipment, such as blowers, trimmers, edgers, chainsaws, etc. This is a very important maintenance part that should be replaced on a regular schedule. Its purpose is to remove contaminants that could clog up the carburetor, which should also be regularly inspected. For this simple repair, slide the new fuel filter onto the fuel line and use a screwdriver to place the clamp tightly over the nipple.
Fix Number FIX11826165
Manufacturer Part Number 90153YRoutine maintenance does not need to be time-consuming, servicing your engine should not take more than 10 minutes with this kit. Inspecting and replacing these parts regularly ensures your engine will run smoothly and efficiently when you need it most. This OEM maintenance kit contains a fuel filter, an air filter, and a spark plug. To properly gap the spark plug you will need to refer to the manual for your specific model.
Fuel Line Grommet
Fix Number FIX8859978
Manufacturer Part Number 13211546730This is a fuel line grommet, and it is used with various lawn and garden equipment. This part prevents leaking fuel and fumes. The grommet is placed in the fuel tank to seal the opening area where the fuel line and the fuel tank connect. A worn grommet is a safety hazard because it will cause fuel to leak from the tank. We recommend when replacing it to also replace the fuel line. Before starting this repair make sure to drain the fuel from the tank, and remove the spark plug.
Fuel Tank Vent
Fix Number FIX9183121
Manufacturer Part Number A356000031This check valve or the fuel tank vent is connected to the fuel tank in the following products: hedge trimmer, leaf blower/vacuum, chainsaw, edger, engine, tiler, auger, water pump, chipper shredder, sprayer, and brush cutter. The check valve allows air into the fuel tank to prevent vacuum when the fuel is being fed through the fuel line. Tip: if the vent is clogged, your engine may stall. Usually, the vent line is connected to a fuel grommet that is installed on the fuel tank. The tools needed for this installation are: needle-nose pliers and a small slotted screwdriver. Remember to wear work gloves to protect hands. Refer to the manual for an accurate repair guide.
Fix Number FIX9261895
Manufacturer Part Number 13201309820
Spark Arrester Screen
Fix Number FIX8867212
Manufacturer Part Number 14586240630
Spark Plug Cap Spring
Fix Number FIX9263507
Manufacturer Part Number 15901103432
Fix Number FIX9148697
Manufacturer Part Number 90050000005This nut is used for a variety of handheld gardening tools. The nut has multiple applications depending on the tool you are using. Refer to the diagram provided by the manufacturer for installation instructions and nut location in a specific tool. This lock nut is used to resist loosening when threaded onto a bolt. *Please note: this part is sold individually. The measurements are: 5mm.