Poulan Chainsaw Carburetors

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12628464

Manufacturer Part Number

530071835

This is a single OEM purge bulb, also sometimes referred to as a primer bulb. It is usually located close to the starter rope. By pressing down on the purge bulb, this forces fuel into the fuel line from the fuel tank and into the carburetor to help get the engine started. Due to its constant contact with fuel, the bulb is prone to damage over time and will need to be replaced.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12628464

Manufacturer Part Number

530071835

This part includes one primer bulb and two screws. These OEM parts are designed for gas chainsaws. The purge bulb is prone to cracking and breaking over time due to its constant contact with fuel. For this repair, start by removing the broken primer bulb from the unit, disconnect fuel lines and short the fuel line from the carburetor and long fuel line from the fuel tank. Next, connect the fuel lines to the new primer bulb and fit the fuel lines onto the fittings. Install the new primer bulb and secure it with the two screws.

Fix Number

FIX9003852

Manufacturer Part Number

530047721

If your engine is having trouble starting, you may be in need a new purge bulb. When the engine has been sitting for a while, unused, the fuel will drain and eventually dissolve out of the carburetor. The next time you go to use your equipment, the engine will not start until the carburetor has fuel in it. The purge bulb, also commonly referred to as a primer bulb, manually pumps fuel back into the carburetor, while purging air out. If the purge bulb is malfunctioning, you will need to pull the starter rope numerous times until the carburetor diaphragm can pump the right amount of fuel back into carburetor for the engine to start. This purge bulb is prone to hardening and cracking over time because it is in continuous contact with fuel and will need to be replaced. This part is sourced directly from the manufacturer and sold individually.

Fix Number

FIX9003852

Manufacturer Part Number

530047721

This part includes one primer bulb, also known as a purge bulb. This high-quality replacement part is sourced right from the original manufacturer. When the engine of your equipment has been left unused for an extended period, the fuel will drain and evaporate out of the carburetor. To start the engine again there needs to be fuel in the carburetor. The purpose of the primer bulb is to manually pump fuel into the carburetor for an easier start. Due to its constant use and exposure to fuel it will likely crack and damage over time and will require replacing. Before you begin this repair be sure to empty the fuel from the tool.

Fix Number

FIX16365453

Manufacturer Part Number

545081885

This is an Original Manufacturer Approved Carburetor Kit which includes a Metal Body Walbro WT89 Carburetor, Plastic Grommet and a Plastic Air Filter Housing. It is used on a variety of Poulan Gas Powered Chainsaws. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.

Fix Number

FIX16365440

Manufacturer Part Number

545070601

This is an authentic replacement carburetor which is supplied by the original equipment manufacturer for use with Craftsman chainsaws. The purpose of this part is to mix the air and the gas before the combustible mix goes into the engine, if the engine won\\\'t start and the tank is full of fresh fuel or if the engine starts and then quickly dies, the carburetor is likely the problem. Please note this high-quality metal body component is sold individually, it includes the primer bulb. Zama W-26

Fix Number

FIX9285128

Manufacturer Part Number

530069844

This is a carburetor repair kit, but it may also be known as a carburetor gasket or diaphragm kit, for your lawn equipment. This assembly is used to replace the gaskets in your machine. If you are having problems with your carburetor, this kit most likely takes care of it. Note: The beige piece pictured has been redesigned. It no longer has the 4 corner holes. It now only has 2 corner holes at a diagonal. To replace these items, you will need a screwdriver and pliers.

Fix Number

FIX10044036

Manufacturer Part Number

D10-WAT

This is a genuine OEM replacement part sourced directly from Walbro. If the engine in your lawn and garden equipment is running rough, the carbonator might need to be cleaned and rebuilt. This kit is commonly used for chainsaws, trimmers, leaf blowers, and edgers. Over time the carburetor gets dirty and parts begin to wear out, instead of replacing the carburetor you can replace the gaskets and diaphragms for increased performance. The kit includes all of the gaskets and diaphragms you will need to rebuild your 2-cycle engine carburetor. When the rebuild is complete be sure to check all connections before running, and while testing ensure there is only a small amount of fuel in the tank. To complete this job you will need a screwdriver and a pick.

Fix Number

FIX10034285

Manufacturer Part Number

95-526-9-8

This is a genuine Walbro replacement part. The metering side of your carburetor is a self adjusting vacuum based system, the diaphragm moves depending on the amount of fuel being pulled into the motor. At higher speeds more fuel is being pulled into the engine, the diaphragm compresses and the pin in the center of the diaphragm pushes on the metering lever, which lifts the regulator inlet needle and allows more fuel to travel from the pump into the reservoir. This is why it is important to ensure your metering diaphragm is in good shape, it is a very important part of the fuel regulator assembly on your carburetor, which ensures your engine is getting the appropriate amount of fuel to run smoothly.

Fix Number

FIX10048119

Manufacturer Part Number

K10-WAT

This is a genuine Walbro replacement part. The carburetor is responsible for regulating the amount of fuel and air that make it to the engine this ensures the fuel is burning properly in your outdoor power equipment. Over time the carburetor gets dirty and parts begin to wear out, it doesnt mean you need a new one. This kit gives you all the parts you need to clean and rebuild your carburetor. Signs your carburetor is clogged or dirty and needs to be cleaned are that the engine is not running properly, it is not running at all, it will not stay running, it is difficult to start, or if it emits a lot of smoke. In order to successfully rebuild your carburetor we suggest that as you disassemble the old carburetor pay attention to the order and placement of the parts you are removing, when reassembling reverse the removal order. When you are finished rebuilding the carburetor be sure to inspect all connections before running. Place only a small amount of fuel in the tank while testing the new carburetor. To complete this job you will need a screwdriver and a pick.