Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
Drive Belt and Motor Isolator Kit
Works With Model MAH21PDA3W!
$40.58
In Stock
- Fix Number:
- FIX2003327
- Manufacturer #:
- 12001788
- Manufactured by:
- Whirlpool
Works With Model MAH21PDA3W!
- Product Description
- This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.
- Works with the following brands:
- Maytag, Crosley, Amana
- Works with the following products
- Washer, Washer Dryer Combo
- Fixes the following symptoms
- Burning smell, Will not agitate, Spins slowly, Will not drain
- Part# 12001788 replaces these:
- AP4009041, 785411, 12001435, 12001788, 12001788VP, 22002040, 22002313
Part Number Cross Reference
Product Description
This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.
-
Works with the following brands:Maytag, Crosley, Amana
-
Works with the following products:Washer, Washer Dryer Combo
-
Fixes the following symptoms:Burning smell, Will not agitate, Spins slowly, Will not drain
-
Part# 12001788 replaces these:AP4009041, 785411, 12001435, 12001788, 12001788VP, 22002040 ... Show more , 22002313 Show less
Videos For installing this part.
Replacing your Drive Belt and Motor Isolator Kit
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts Additional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- Timothy from Monroe, GA
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Motor ceased working
Parts (motor/motor controller board) arrived within two days of ordering. Instructions were extremely accurate. Machine was up and running within an hour of the start of the repair. Replacement parts were different than original; wiring harness on original was attached to the Motor Controller Board and plugged into the motor; reverse a
... Read more
pplication with new parts. I had difficulty with the plug from the motor to the controller board as there was no specific plug to place it into as the other wires on the unit. This plug seated onto the end of the physical board. For a visually impaired individual; this was the most challenging aspect of the repair.
Read less
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing Maching Made lots of Squealing during spin Cycle
I had some help. The instructions were pretty clear about diss-assembly. I had to hit the shaft out with a sledge hammer and a block of wood. the confusion came as two sets of bearing seals were provided.I finally figured out that on my unit I had to use the thicker one without the spacer. Putting it back together was laborious as the
... Read more
clips that held the front rubber seal on the tub were very difficult to put on. The belt that I ordered had the same part number as my belt but it was 2 inches too short so I had to use my original belt. It looked in good shape so I am not worried and it is easy to get to if I do have to replace it later on.
Read less
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Parsons, KS
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer spin cycle would count down to 4 minutes then went back to 7 minutes with wet clothes
I took the back off, took out the old belt. The bolt holding the drum pulley had worked loose so I tightened it before putting the new belt on. I replaced the motor rocker bushings according to the instructions before mounting the new belt. I ran it around several times by hand to stretch the belt and insure the belt wouldn't slip off bef
... Read more
ore putting the cover on. Then I ran it through spin cycle and quick wash a couple of times to insure everything was ok.
Read less
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Bradley, ME
- Parts Used:
- 12001788
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drum drive belt slipping
Removed four screws to remove the rear access panel, then rotated the drum while pulling the belt towards me to remove the belt from the drive motor and drum pulleys. Then reversed the procedure to install the new belt. It actually took longer to unhook/rehook the hoses and pull the machine out/back then it did to change the belt.
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James Stanley from Bedford, VA
- Parts Used:
- 12001788
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set, Wrench set
the new belt was shorter than the old one.
The bushing replacement was to difficult. the belt installation was a bear.
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Sun Prairie, WI
- Parts Used:
- 12001788
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
worn out belt.
watch repair video
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- duane from sun prairie, WI
- Parts Used:
- 12001788
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
worn out belt.
watched repair video
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX2003327
Manufacturer Part Number: 12001788
Manufacturer Part Number: 12001788
Brand
Model Number
Description
✖
Mail-In Recycling Rebate