Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
Door Boot Seal
Works With Model IFW7200TW10!
$277.48
In Stock
- Fix Number:
- FIX11741579
- Manufacturer #:
- WP34001432
- Manufactured by:
- Whirlpool
Works With Model IFW7200TW10!
- Product Description
- Also known as Door Diaphragm or Bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
- Works with the following brands:
- Amana, Maytag, Inglis
- Works with the following products
- Washer
- Fixes the following symptoms
- Leaking
- Part# WP34001432 replaces these:
- AP6008441, 34001432
Part Number Cross Reference
Product Description
Also known as Door Diaphragm or Bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
-
Works with the following brands:Amana, Maytag, Inglis
-
Works with the following products:Washer
-
Fixes the following symptoms:Leaking
-
Part# WP34001432 replaces these:AP6008441, 34001432
Videos For installing this part.
Replacing your Door Boot Seal
Replacing your Door Boot Seal
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- Scott from St. Paul, MN
- Parts Used:
- WP34001432
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door Boot Seal Had Piece Missing So It Leaked
1] Remove door. 2] Remove top of washer(2 screws at rear of machine) 3] remove soap dispenser and screw underneath it. 4] Remove screws at top of machine holding switch panel. 5] Move switch panel out of way but do not disconnect harness. 6] Remove screws holding door latch assembly to front of machine. 6] Remove spring loaded seal r
... Read more
etainer from outer part of seal. Remove screws holding machine front on. This machine had lots of soap spilled by previous home owner. As such, the 2 screws adjacent to soap dispenser were corroded and would not move. I drilled them down center with a small bit and removal was easy after. 7]Bring machine front up off the tabs on bottom. 8] Using a 5/16 socket on a quarter drive ratchet and short extension loosen clamp holding seal at rear of seal. 9] Remove seal. Carefully install new seal making sure it is seated fully before tightening clamp. Also make sure clamp is seated all around seal before tightening. 10] Reverse earlier steps to complete repair.
Read less
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Bremerton, WA
- Parts Used:
- WP34001432
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
No problems
We watched the video that was sent in our email. The video made it very easy. The only problem we encountered was a screw under the soap dispenser was corroded and had to be drilled out.
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX11741579
Manufacturer Part Number: WP34001432
Manufacturer Part Number: WP34001432
Brand
Model Number
Description
✖
Mail-In Recycling Rebate