Watch the install video
11738845-1-M-Whirlpool-WP21002026-Snubber Ring
Part Location Diagram of WP21002026 Whirlpool Snubber Ring
See part 52 in the diagram
Replacing your Maytag Washer Snubber Ring
( Grid squares measure 1x1 inch )
11738845-1-S-Whirlpool-WP21002026-Snubber Ring 11738845-2-S-Whirlpool-WP21002026-Snubber Ring Part Location Diagram of WP21002026 Whirlpool Snubber Ring Replacing your Maytag Washer Snubber Ring

Snubber Ring

Works With Model 6002A!

Rated by 10 customers 

?

A Bit Difficult 

More than 2 hours 

Ratings submitted by customers like you who bought this part.

?
$13.11
In Stock
Fix Number:
FIX11738845
Manufacturer #:
WP21002026
Manufactured by:
Whirlpool
Works With Model 6002A!
Product Description
This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operating. If your washer shakes a lot and makes loud noises, then it is best to replace this part to solve your problem. The tools required for this repair are: short flathead screwdriver, flathead screwdriver, Philips screwdriver, 1/4 inch nut driver, 5/16 inch nut driver, 3/8 nut driver, ratchet with extension, putty knife, locking pliers, slip joint pliers, and 3/8 inch socket.
Works with the following brands:
Maytag, Norge, Admiral, Magic Chef
Works with the following products
Washer
Fixes the following symptoms
Spins slowly, Shaking and Moving, Will not agitate
Part Number Cross Reference
Part# WP21002026 replaces these:
AP6005786, 21001161, 21002026, 35-2357, 35-3699, 35-3788, WP21002026VP
1 Installation Video 3 Related Parts 2 Questions and Answers 10 Installation Instructions Model Compatibility
Product Description Part Videos Questions and Answers Related Parts Installation Instructions Model Compatibility

Product Description

This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operating. If your washer shakes a lot and makes loud noises, then it is best to replace this part to solve your problem. The tools required for this repair are: short flathead screwdriver, flathead screwdriver, Philips screwdriver, 1/4 inch nut driver, 5/16 inch nut driver, 3/8 nut driver, ratchet with extension, putty knife, locking pliers, slip joint pliers, and 3/8 inch socket.

  • Works with the following brands:
    Maytag, Norge, Admiral, Magic Chef
  • Works with the following products:
    Washer
  • Fixes the following symptoms:
    Spins slowly, Shaking and Moving, Will not agitate
  • Part# WP21002026 replaces these:
    AP6005786, 21001161, 21002026, 35-2357, 35-3699, 35-3788 , WP21002026VP Show less

Videos For installing this part.

Replacing your Snubber Ring

Replacing your Snubber Ring

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
  • 1
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barry
October 3, 2021
Maytag washer stopped spinning but pumps the water out. How do I resolve this problem
For model number MAV6548AWW
Fix.com logo
Hello Barry, Thank you for the question. The most common issues is a worn or broken Belt. We suggest checking the Belt first to verify it is intact. If the Belt is good, you can check the Transmission Pulley and Bearing Kit for wear or damage. We hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Transmission Pulley and Bearing Kit
$69.83
In Stock
Drive Belt - 52 inches long
$37.77
In Stock
Chuck
January 4, 2023
Washer doesn’t spin at high speed. Spins but not fast enough to get water out clothing. Changed belt and pulley kit on bottom of transmission
For model number MAV408DAWW
Fix.com logo
Hello Chuck, thank you for contacting us. If replacing the belt and pulley kit does not solve the issue, we would recommend checking the motor, part number FIX11738839. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!

Was this helpful?
Thank you for voting!
Related Parts:
Motor with Pulley
$163.40
In Stock
Suspension Springs - Kit of 6
$68.55
In Stock
Part Number: FIX2004049
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot during operation, it coul...
Suspension Spring
$11.80
In Stock
Part Number: FIX11738823
This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.
Drive Belt - 51 inches long
★★★★★
★★★★★
(1)
$10.98
In Stock
Part Number: FIX11738882
This is a V-style drive belt that measures approximately 51-inches long and 3/8-inches wide. This part connects the drive motor to the drive system in the washer to turn the basket. It is prone to wear with time and requ...

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 2.2 / 5.0, 10 reviews.
  • 1
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
Brandon from Keller, TX
Parts Used:
35-6714, WP22004376, 12002213, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer would run and agitate but would not spin.
Prior to the spin cycle not working, the washer would make a loud screeching noise when the spin cycle would stop. I wasn't sure if there was a problem with the break rotor or some bearing was out. Due to the washer's age, I decided to go ahead and replace the pulley, brake rotor, motor pivot spring and snubber ring components.
I be gan by unplugging the unit first, securing the lid with duct tape and laying the washer on its front face. I removed the belt and transmission pulley per instructions contained in the replacement kit. Mainly consists of popping the "E" ring off with a screwdriver. Once the pulley was off, I stood the washer upright and to access and remove tub. Having the tub out made it easier to compress the brake spring when re-attaching the brake stator. Removing the tub is easy, I just popped off the tub cover and tilted the tub around to ease the tension and remove the bottom springs with pliers (this may require an assistant). With the tub removed, I turned it over to remove the brake stator. USE CAUTION WHEN REMOVING THE BRAKE STATOR. A 200 LB BRAKE SPRING IS UNDER IT AND IS UNDER TENSION. With the new brake rotor and brake stator secured, I replaced the snubber ring and motor pivot spring. I put it all back together in reverse order and it spun like a top, is quieter and stops on a dime!
Read less
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Minong, WI
Parts Used:
12002773, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The washer was jumping all over during spin cycles
The most difficult thing to do was to install the springs. I removed the sides and back, which made it much easier. Otherwise, I followed the instructions which were provided by others on the site.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Rotonda West, FL
Parts Used:
35-6714, 35-6918, WP21001910, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set
Washer making ratcheting sound when agitating.
Taking it apart was easy. I found that the new parts did not allow the slip ring that came with the new kit to fit the shaft even with the thinner washer. The new slip ring seemed to be thicker than the old one. I ended up using the old large pulley, the old cam and the old slip ring and thin washer to get it to fit. It did solve the nois e problem.
Read less
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RONALD from METAIRIE, LA
Parts Used:
WP21002026
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Spring tension on drum.
This spring have so much tension they cannot be removed with one hand like the indicate in the video. Tube must be wedged towards the spring trying to be removed. Vise grips must be attached to the lower part of the spring not the upper and pry bar is needed to pry spring loose from base of unit. Be careful nothing slips where prying, there is a lot of tension on the springs.
Read less
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from Granite Falls, NC
Parts Used:
WPW10717210, WP21002026, 12002773
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Tub out of balance
Took springs off turn tube upside down undone screws and replaced snubber ring. Suspension springs put 3 on then used rolled up towel to hold tub tilted to side.Followed some. videoson how to fix it
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Vandling, PA
Parts Used:
WP21352320, WP21002026
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
machine shook and walked
I followed the video which is great, the repair went smoothly and it fixed the problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roderick from Mckinney, TX
Parts Used:
12001908, WP21002026
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
washer was shaking and walking , lid switch didn't engage
I did everything by the instuctions on your site, i used the vicegrips to attach the springs , i tipped the tub as much in the direction of the springs being installed and latched on the spring with vicegrips And attached it, no problem.The ring was no problem at all per instructions, the lid switch was ok installed the way it came off. T hanks, Rod
Read less
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from St Marys, WV
Parts Used:
WP22004333, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
washer would not stay in balance and at times cold water would not completely shut off
case top and front had to be removed, belt to pully removed, tub springs removed, install new snubber ring, remove and replace water valve. Hardest part of repair was putting springs back onto tub used vise grips to assist.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Springfield, VA
Parts Used:
WP21002026, WP21001598
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Wash shakes and moves during spin cycle
The on-line video from this site was extremely helpful! It showed me almost exactly what to do. The only difference was that my washer did not have an access panel in the back of it like the one in the video. I had to remove the skin "shell" of the washer to get around to the back of the tub unit. It wasn't too hard and the entire rep air was done in about 2 hours. This was the first time I've ever attempted a repair like this so I'm sure that added to my repair time.
Read less
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diana from ShowLow, AZ
Parts Used:
WP35-6918, WP35-6714, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Machine was noisy during wash cycle and had teh infamous finger on wet glass screach.
After watching the online video and info I decided to tackle the repair from the bottom of the machine, tilted against the wall. I removed the lower pulley and belt then rotated out the # 10 screws with the 2 inch ones to relieve the brake rotor spring tension. The brake stator came off easily, with the spring and brake rotor to follow. S ince the tub rests on the Snubber Ring, it is not possible to change it out from the bottom. From my visual inspection the snubber ring appeared intact, so left the old one in place. I installed the new Brake Rotor and Stator and put the lower pulley and belt back on. Tested the machine and it ran smooth as new.
Read less
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1

Model Compatibility

This part works with the following models:
Fix Number: FIX11738845
Manufacturer Part Number: WP21002026
Brand
Model Number
Description
Norge
6002A
Washer - WASHER
Norge
6430
Washer - WASHER
Norge
6432A
Washer - WASHER
Norge
6432A REV A
Washer - Norge Washing Machine Model 6432A REV A (6432AREVA) Parts
Norge
6432A REV B
Washer - Norge Washing Machine Model 6432A REV B (6432AREVB) Parts
Norge
6432A REV C
Washer - Norge Washing Machine Model 6432A REV C (6432AREVC) Parts
Norge
6432A REV D
Washer - Norge Washing Machine Model 6432A REV D (6432AREVD) Parts
Norge
6433A
Washer - WASHER
Norge
6440A
Washer - WASHER
Norge
6440A REV A
Washer - Norge Washing Machine Model 6440A REV A (6440AREVA) Parts
Norge
6440A REV B
Washer - Norge Washing Machine Model 6440A REV B (6440AREVB) Parts
Norge
6440A REV C
Washer - Norge Washing Machine Model 6440A REV C (6440AREVC) Parts
Norge
6440A REV D
Washer - Norge Washing Machine Model 6440A REV D (6440AREVD) Parts
Norge
6440A REV E
Washer - Norge Washing Machine Model 6440A REV E (6440AREVE) Parts
Norge
6440A REV F
Washer - Norge Washing Machine Model 6440A REV F (6440AREVF) Parts
Norge
6440A REV G
Washer - Norge Washing Machine Model 6440A REV G (6440AREVG) Parts
Norge
6440A REV H
Washer - Norge Washing Machine Model 6440A REV H (6440AREVH) Parts
Norge
6440A REV J
Washer - Norge Washing Machine Model 6440A REV J (6440AREVJ) Parts
Norge
6440A REV K
Washer - Norge Washing Machine Model 6440A REV K (6440AREVK) Parts
Norge
6443A
Washer - WASHER
Norge
6443A REV D
Washer - Norge Washing Machine Model 6443A REV D (6443AREVD) Parts
Norge
6443B
Washer - WASHER
Norge
6530A
Washer - WASHER
Norge
6530A REV A
Washer - Norge Washing Machine Model 6530A REV A (6530AREVA) Parts
Norge
6530A REV B
Washer - Norge Washing Machine Model 6530A REV B (6530AREVB) Parts
Norge
6530A REV C
Washer - Norge Washing Machine Model 6530A REV C (6530AREVC) Parts
Norge
6530A REV D
Washer - Norge Washing Machine Model 6530A REV D (6530AREVD) Parts
Norge
6530A REV E
Washer - Norge Washing Machine Model 6530A REV E (6530AREVE) Parts
Norge
6530A REV F
Washer - Norge Washing Machine Model 6530A REV F (6530AREVF) Parts
Norge
6530A REV G
Washer - Norge Washing Machine Model 6530A REV G (6530AREVG) Parts