See part 35 in the diagram
( Grid squares measure 1x1 inch )
Rear Drum Felt Seal
$
58.64
In Stock
In Stock
Fix Number: FIX8691753
Manufacturer #: W10612022
Manufactured by:
Whirlpool
-
Product Description
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
-
Works with the following brandsWhirlpool, Kenmore, Maytag, KitchenAid
-
Works with the following productsDryer
-
Fixes the following symptomsNoisy, Marks left on clothes, Takes too long to dry, Will not tumble
-
Part Number Cross ReferencePart# W10612022 replaces these:AP5737110, 279857, 3406130, W10352407, W10389561, W10612022VP, W10663495, W10725245, W10856781
Product Description
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
-
Works with the following brands:Whirlpool, Kenmore, Maytag, KitchenAid
-
Works with the following products:Dryer
-
Fixes the following symptoms:Noisy, Marks left on clothes, Takes too long to dry, Will not tumble
-
Part# W10612022 replaces these:
Videos For installing this part.
Replacing your Rear Drum Felt Seal
Installation Instructions Provided by Fix customers like you.
Average Repair Rating: 3.4 / 5.0, 5 reviews.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:David from Kalamazoo, MI -
Parts Used:W10612022 -
Difficulty Level:Very Easy -
Total Repair Time:30 - 60 mins -
Tools:Nutdriver, Screw drivers
Drum felt seal came off and was pinched between the drum & back panel
Unplugged the unit, Removed the top, front panel and drum. Cleaned the old glue from the drum and fitted the new felt seal. I then glued the new seal in place in sections of approximately 15 to 20 % of the drum diameter. I clamped the felt seal in place for 5-10 minutes and continued the process around the diameter of the drum. I let the glue dry & reinstalled the drum, its belt and idler pulley. I reinstalled the front panel and used a common table knife to make sure the drum seal was properly seated; turning the drum counter clockwise. Once seated, I reinstalled the top & filter; turned the dryer on and relished in the silence. I spent more time than needed but that was my choice. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Paul from San Antonio, TX
-
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Noisy operation
I removed the screws at the lint filter then released the fasteners at the front to allow me to open the top cover. I then unplugged the door switch and removed the 2 screws at top of front cover and removed the front. I then lifted the drum out of the dryer and removed the rear drum felt seal per instructions included with part. then glued the new seal to the rear of the drum. allowed the glue to dry (about 30 minutes) while waiting for the glue to dry I replaced the front felt bearing and seal. re-assembled the dryer and tested. Wow what a difference. I also watched both videos available on the site for the repairs I was making. Suggest when replacing the rear seal that you glue about 2 feet around and wait for the glue to set up (about 10 minutes) then install the remainder of the seal and glue in place.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:John from Clearwater, FL
-
Parts Used:W10612022
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
worn out drum seal causing scrapping noise
followed a you- tube video. it was very simple to follow and the instructor in the video covered every step.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Mike from Bowling Green, OH
-
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
drum making load noise when turned on
I removed drum from cabinet and noticed one of the drum support rollers was froze to spindle and wore down in one spot. Both front and rear drum seals were also worn. I ordered the parts and they arrived in 2days. The front drum seal was easy to install but not so much for the rear seal. I installed the rear seal before gluing bye clamping the seal every foot with 6inch clamps, 5 total and then start gluing and moving the clamps, to one side. as needed. I have done several of these now and this is the best way I've found. Support rollers are easy just need a pair of pliers and a small flat head screw driver. Installing the belt over the drum bye yourself is not easy but can be done. There are several videos online that are a big help.
Was this instruction helpful to you?
Thank you for voting!
★
Customer Reviews
Filter By Rating:
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Thomas G B - September 27, 2019
Belt
Exact fit
Model Compatibility
This part works with the following models:
Fix Number: FIX8691753
Manufacturer Part Number: W10612022
Manufacturer Part Number: W10612022
Brand
Model Number
Description