We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ethan
December 6, 2022
I was told to replace this part on my dryer because I am getting a vent occlusion alert but there isn’t an occlusion. Is it correct to do this? Thank you.
For model number DV50K8600EV/A3
Hello Ethan, thank you for contacting us. Provided that the vents are clean, we would recommend checking the blower wheel, part number FIX4212790, and its motor, part number FIX4204647, and make sure they are working and able to keep the air in flow. If this does not help, the issue is probably related to the thermistor, part number FIX4204984, and the control board, part number FIX11766599. Please reach out to customer service if you need help placing an order. Glad to be of help!
My dryer is not heating. How can I tell if it is the heating element or the thermistor?
For model number DV448AEP/XAA
Hello Sonia, Thank you for the question. In order to confirm if the Heating element or the Thermistor are faulty, they would need to be tested with a Multimeter. The Thermistor should read 10,000 ohms at 77°. The Element should be reading between 0 - 50 ohms. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
UNPLUG first! remove vent hose, remove inside vent tube, (three screws), remove the top panel, (two screws, on back top), remove front panel with door,(4 screws on top, & 3 screws inside door)..to remove heater, remove one screw in the front, and unplug the wiring, then snake it out the back.. install new and put back together following
... Read moresteps back to start!!
Dryer would shut off after a few minutes into drying cycle. Not heating properly.
I took the outer parts off the dryer including the control panel. Then I went under the drum and took out the old thermistor and plugged the new one in. I didnt have to take the drum out to do it. A person should be somewhat mechanically inclined to do this. The most difficult task was taking all the screws out to get to the part that
... Read moreneeded replacing.
dryer not comming on showing code that looked like upside down f s
removed top of dryer along with control panel and front of dryer. Thermistor is at the bottom in front. removed wires and part. replaced part.Still had code and dryer would not start.Found out I needed to clear code. This is what we did to clear. Press and hold Chime and temp buttons for 3 secthen press wrinkle prevent.Should get a d in t
... Read morehe display.after that rotate cycle knob.after that press sensor dry and time keys for 3 sec. power off to exit power on and dryer works fine.
The video is really helpful in the dis-assembly process of a Samsung dryer. These coils fit the Samsung DV328 even though it's not listed. - PS334310 There were a lot of pieces to take apart in order to get to the coils. None of it was hard, just a lot and it was all done with a single Phillip's screwdriver.
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX4204984
Manufacturer Part Number: DC32-00007A
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
