Maytag/Maytag_Thumb/55904.gif
See part 1 in the diagram
Replacing your Maytag Dryer Multi Rib Belt - 91-5/8 Inches play video
( Grid squares measure 1x1 inch )

Multi Rib Belt - 91-5/8 Inches

★★★★★
★★★★★
1 Review
$ 31.33   In Stock
Fix Number: FIX11741110
Manufacturer #: WP33002535
Manufactured by: Whirlpool

Product Description

At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.

Videos For installing this part.

Replacing your Multi Rib Belt - 91-5/8 Inches

Replacing your Multi Rib Belt - 91-5/8 Inches play video

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.0 / 5.0, 34 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this.
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Shawn from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
Squeaky
Followed youtube tutorials, pretty straightforward. Take pictures of where wires connect for door switch, light, et al. Have a shop-vac handy to vacuum all the dust, lint, dog hair, etc that's accumulated over the years inside the unit.My spreader c-clip pliers were not small enough to fit in the holes of those tiny c-clips,had to improvise.Used steel wool to polish all roller shafts, Before re-installing drum and belt, orient yourself to this procedure by practicing threading belt properly before positioning the drum in your way!
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    michael from muncie, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
squeeky
removed dryer, set up on roll around work bench, watched your repair video, took my time and cleaned with air compressor and shop vac. did it all in standing position.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very loud rubbing/squeaking noise
Watched 2 YouTube videos. 1. How to take apart a dependable care dryer. 2. How to replace a belt on a maytag dryer. We replaced all the parts. It was eeasy. When putting dryer back together make sure felt is straight. We did have to take it apart again there was felt sticking out inside the dryer and it caused the drum to not spin. Everything works great. And Thank you parts select. I received the right parts in 2 days without paying extra. I will use you again.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    John from Zephyr, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
The roller bearings worn out causing belt to break
First thing was to watch this video on Youtube on the take down of this dryer and determine what caused the malfunction.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud screeching noise, intermittant but with increasing regularity when running dryer.
Took off the door, and then front panel and shroud/bulkhead according to video instructions. Removed the belt, and then the tumbler. Found that the roller assembly bearing was rubbing against the shaft support on lower right side. I replaced both rollers, they come as a pair, the idler wheel, the front glides, the blower seal, and the belt. I purchased all these based on suggestions in reviews, but would suggest taking apart to make sure of part needed, in this case it was obvious when I spun the drum support wheels, one was less giving and literally screeched. I did not need a new idler wheel or belt, but used them anyway. The glides looked a little worn, so was good to replace them and the blower seal seemed a little worse for wear. I cleaned the blower wheel ribs as best as possible and vacuumed everything I could. For the glides, you will need a 1/8" drill bit to drill out old rivets and a rivet gun to replace. For the drum support wheels you will need a pair of C-Ring pliers. It was all very straight forward having reviewed the videos. I did raise the cover when working on all of this, which provided much better access and space, and used a bungee cord to help hold the tumbler in place when doing reassemble. Fantastic website, instruction with videos, couldn't be easier. Good luck.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hella Loud
1st off, watch all the video's they supply even before you buy the parts. A lot of knowledge in them. It helped to ensure I bought the right parts to begin with. I removed the front of the machine, removed the brackets holding the lid down. Raised the lid, and did an inspection of everything. Removed the front so I could remove the drum. Once that was down, piece of cake. I got out the vacuum, vacuumed out everything, then moved to removing the rollers. Because my tool broke to remove the retaining clip from the front, I had to use a 1/2" wrench to removed the roller studs. Rebuilt the drum support rollers, and put them back on. Next was the idler pulley wheel and bearing and idler arm and shaft. Another piece of cake. I decided to not replace the front glide as it looked fine. NOW THE TRICKY PART. Putting the new belt on and putting the drum back in. Watched that video 4 times. Finally got it. Of the little over two hours, 30 minutes was spent on this part. Put everything back together from there a cake walk. YOU DO NOT NEED TO REMOVE ANY WIRES FROM ANYTHING EITHER. Hope this helps.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    James from MOGADORE, OH
  • Parts Used:
    WP9703438, WP33002535, 33001790
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
The blower wheel was deteriorating around the axle
Step 1. I disconnected the electrical outlet Step 2. Took the front panel then the door and then the panel that holds the tumbler. Took the belt off the tumbler then the tumbler. Took the housing cover for the blower wheel off. Took the clip off the blower wheel to the axle of the motor. Replaced with new blower wheel and belt and cleaned the inside of the dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    ROBERT from Germantown, TN
  • Parts Used:
    WP33002535, 12001541
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Squeaky, worn clothes dryer drum rollers
I watched 2 different U-Tube videos, studied tools needed, tool sizes required and dis-assembly/assembly techniques. When viewing videos be sure to visualize how to properly install the drum belt on the motor drive and tensioner. Prep your repair area-clear areas to put dissembled parts, screw etc.. Take the time to remove all internal dust and lint in the vent tubing and front drum face(Motor fan area & lint screen area) and rear lint exhaust tube, Photo all wire connections that are to be unplugged to review for re-assembly. No need to move the dryer or remove rear dryer panel: all you need is a good closed wrench ratchet(boxed on one end/circular ratchet on the other) and a pliers to remove the two rollers and re-install them. If you re-use the roller pins clean them thoroughly.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Frank from Colorado Springs, CO
  • Parts Used:
    WP33002535
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
would not tumble
watch the video and followed the intructions not hard to do safed several dollars doing it yourself works great now thank you
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating: (1 Review)
4.0
★★★★★
★★★★★
Filter By Rating:
  • 5
    0
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0
    Sort by:
    Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Compatibility
      This part works with the following models:
      Fix Number: FIX11741110
      Manufacturer Part Number: WP33002535
      Brand
      Model Number
      Description
      Crosley
      CDE4205AYJ
      Dryer - Residential
      Crosley
      CDE4205AYW
      Dryer - Residential
      Crosley
      CDE4205AZJ
      Dryer - Residential
      Crosley
      CDE4205AZW
      Dryer - Residential
      Crosley
      CDG4205AWJ
      Dryer - Residential
      Crosley
      CDG4205AWW
      Dryer - Residential
      Maytag
      MDB9206AWW
      Dryer - Maytag Dryer Model MDB9206AWW Parts
      Maytag
      MDE14PDACL
      Dryer - Electric
      Maytag
      MDE14PDACQ
      Dryer - Electric
      Maytag
      MDE14PDACW
      Dryer - Electric
      Maytag
      MDE14PDADL
      Dryer - Electric
      Maytag
      MDE14PDADW
      Dryer - Electric
      Maytag
      MDE14PDAGW
      Dryer - Electric
      Maytag
      MDE14PNAGW
      Dryer - Gas
      Maytag
      MDE14PNAYW
      Dryer - Gas
      Maytag
      MDE14PNAZW
      Dryer - Gas
      Maytag
      MDE14PRAYW
      Dryer - Gas
      Maytag
      MDE14PRAZW
      Dryer - Gas
      Maytag
      MDE14PSADW
      Dryer - Electric
      Maytag
      MDE16CSAGW
      Dryer - Electric
      Maytag
      MDE16CSAKA
      Dryer - Electric
      Maytag
      MDE16CSAKQ
      Dryer - Electric
      Maytag
      MDE16CSAYA
      Dryer - Electric
      Maytag
      MDE16CSAYQ
      Dryer - Commercial
      Maytag
      MDE16CSAYW
      Dryer - Electric
      Maytag
      MDE16CSAZA
      Dryer - Electric
      Maytag
      MDE16CSAZQ
      Dryer - Commercial
      Maytag
      MDE16CSAZW
      Dryer - Commercial
      Maytag
      MDE16CSDGW
      Dryer - Electric
      Maytag
      MDE16CSDYW
      Dryer - Electric