Kenmore Dryer Multi Rib Belt - 92-1/4" 341241 | Fix.com

Multi Rib Belt - 92-1/4"

&SeePartX&
346995-1-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4"
346995-2-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4"
346995-3-S-Whirlpool-341241            -Multi Rib Belt - 92-1/4"
https://fixcom.azureedge.net/Schematics/Maytag/UTGT4VNQ.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
This part fixes the following symptoms: Will not tumble, Noisy, Will not start, No heat or not enough heat, Takes too long to dry, Heat stays on after drum has stopped, Too hot, Touchpad does not respond.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Dryer, Washer Dryer Combo.

Installation Videos

Replacing your Kenmore Dryer Multi Rib Belt - 92-1/4"
Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Fixes the following symptoms:
  • Dryer drum stopped turning but fan still blows
Tools used for this repair:
  • 5/16" Nut Driver
  • Phillips Screw Driver
  • Putty Knife

Related Parts

Installation Instructions

Showing 1-10 of 72 Instructions
>
page 1 of 8
<

Not spinning

follow the vidio

Were these instructions helpful?

9 of 13 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Multi Rib Belt - 92-1/4"
Difficulty Level: Very Easy
Total Repair Time: 30 - 60 mins
Tools: Screw drivers
Customer: carolyn from phila, PA

Motor would overheat and shut off in the middle of the cycle.

Replaced the drive motor using the installation video listed with the part. The instructions were accurate and very easy to follow.

Were these instructions helpful?

5 of 5 people found these instructions helpful
Parts Used: Multi Rib Belt - 92-1/4" , Drive Motor with Pulley
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Customer: Mike from NORRISTOWN, PA

Dryer drum would not tumble (rotate)

Take out dryer screen, and remove 2 retaining screws. Use putty knife to push both clips on the front corners of the top of the dryer to lift top off. The front of the dryer only has 2 retaining screws around where the clips are to remove the top. Remove those screws then lift up to disengage the hooks the front is sitting on. The drum should hang freely. Remove old belt/idler pulley assembly. When the new belt and pulley assembly are installed (slide the new belt around the drum, through the pulley assembly and around the shaft to the motor), rotate the drum a couple times to make sure it is lined up correctly. Then reassemble the dryer.

Were these instructions helpful?

4 of 4 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Multi Rib Belt - 92-1/4"
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: charlie from orlando, FL

The dryer squeeled the full time it was turned on.

I called my boyfriend

Were these instructions helpful?

2 of 2 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Cathy from WHITE HAVEN, PA

Dryer was screeching

Very simply followed the instructional videos on the website. Their step by step instructions were easy to follow and the video detail was great. I found the website in a search for diagnosing a noisy dryer. Once I saw the videos and ordered the parts I couldn't wait to complete the repair. It took less then an hour and the dryer runs fine. I hope to get many more years out of it and have no fear that in the future I can complete other repairs if need be.

Were these instructions helpful?

2 of 3 people found these instructions helpful
Parts Used: Rear Drum Support Roller Kit , Front Glide Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: David from Bayville, NJ

Dryer drum didn't tumble.

When reassembling, used a length of nylon cord to suspend the front end of the drum from holes in the side panels of the dryer cabinet, so that I could use both hands to reinstall the front panel. After installing the front panel, untied the cord and pulled it out.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Fred from VASHON, WA

Dryer belt broke

1. All my son
2. Place package with belt on kitchen table.
3. Go out to a meeting.
5. Come home and find note on table that dryer is fixed. ??

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Multi Rib Belt - 92-1/4"
Difficulty Level: Very Easy
Total Repair Time: 30 - 60 mins
Tools:
Customer: Glorianna from SAINT LOUIS, MO

Replaced blower wheel and belt

taking it apart was easy the hard part was removing excess plastic from D shaped hole in wheel. There is so much plastic in center hole that it will not seat on shaft. I had to use a drill and dove tail file to do this project. F.Y.I. this was the second wheel the first i broke when it was half way on the shaft tap lightly my friend.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Blower Wheel , Multi Rib Belt - 92-1/4"
Difficulty Level: Difficult
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: John from Dallastown, PA

Squeeks like crazy while running

I replaced the drum rollers, belt and idler pulley, I had an 80-90% chance that it would fix the issue. The video on the website was spot on in every phase of the repair - just follow it as shown. By spending $45, I bet I'll get many more years out of this machine.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Idler Pulley Assembly , Rear Drum Support Roller Kit , Multi Rib Belt - 92-1/4"
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Screw drivers, Wrench set
Customer: David from Rochester, NH

Squealing noise when running, bad motor bearing; needed new motor.

The instructional videos that this site provides are really great and most helpful. If changing a motor or blower, it will tell you to hold the motor shaft while loosening the blower, (CAUTION: left hand thread). Those instructions would be great for a dryer that is almost new but the likelihood of needing to change the motor or blower wheel on a fairly new dryer would be slim. Because my dryer was not new, as I suspect most needing repairs aren't, I ended up doing what most everyone else had to do and that is,cut the shaft that extends into the blower wheel because that blower wheel absolutely refuses to break free from the motor shaft, most likely because it's seized onto the shaft, probably caused by years of moist air in the blower tunnel, (too bad the factory doesn't put a dab of Never Seize on the threads before assembling it when new). In any case, if you determine that you need a new motor, do yourself a favor and order a new blower wheel at the same time, then plan on cutting the old one off if it fails to budge on your first attempt. I used a Milwaukee M12 Hackzall, which is their smaller mini cordless reciprocating saw, with a 6" blade. A six inch blade is just long enough that it will flex, allowing the space required to get in between the blower and the end of the motor. You might be able to get a full size reciprocating saw in there although it will be tougher. Be careful not to destroy the felt seal on the cabinet wall that keeps the lint out of the main cabinet. Once the motor and blower are free of each other, the rest is simple and quick. If I spent two and a half hours completing the repair, 90% of that was trying to unscrew the blower from the motor. This site is great to do business with, from their large inventory, to their great web site, service, and delivery. Great company!

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Wheel, Blower (Includes Illus. , Multi Rib Belt - 92-1/4" , Drive Motor with Pulley
Difficulty Level: A Bit Difficult
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Wrench (Adjustable), Wrench set
Customer: Roland H from Auburn, ME
Showing 1-10 of 72 Instructions
>
page 1 of 8
<

Model Cross Reference List

This part works with the following models:

Fix Number: FIX346995
Manufacturer Part Number: 341241


Brand Model Number Description
Kenmore10686294140Dryer
Kenmore10686294340Dryer
Kenmore10686294540Dryer
Kenmore10686294740Dryer
Kenmore10686294840Dryer
Kenmore11060012000Dryer
Kenmore11060012001Dryer
Kenmore11060012002Dryer
Kenmore11060022010Dryer
Kenmore1106012510Dryer - ELECTRIC DRYER
Kenmore11060172000Dryer
Kenmore11060172001Dryer
Kenmore11060172002Dryer
Kenmore11060202990Dryer
Kenmore11060212990Dryer
Kenmore11060222510Dryer - DRYER
Kenmore11060222511Dryer - ELECTRIC DRYER
Kenmore11060232000Dryer
Kenmore11060232001Dryer
Kenmore11060232002Dryer
Kenmore11060522900Dryer
Kenmore11060602990Dryer
Kenmore11060612990Dryer
Kenmore1106062110Dryer
Kenmore11060622990Dryer
Kenmore11060702990Dryer
Kenmore11060712990Dryer
Kenmore1106072010Dryer - ELECTRIC DRYER
Kenmore1106072011Dryer - ELECTRIC DRYER
Kenmore11060722990Dryer