GE/GE_Thumb/00009519i03.gif
See part 454 in the diagram
( Grid squares measure 1x1 inch )

Front Drum Slide Kit

$62.29
Fix Number: FIX267600
Manufacturer #: WE25X60
Manufactured by: GE

Product Description

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.3 / 5.0, 5 reviews.
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    • Customer:
      Gary from VINELAND, NJ
    • Parts Used:
      WE25X60
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Wrench set
    Washer was making lound grinding noise.
    Removed screws that comnect top if dryer. Lifted top and secured. Removed screws that vinnect front panel, bur first disconnected wires to door latch shut off top rhs, 2 wires. Replaced the 2 frym gliders and then revered prev steps. Fix the loud noise
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      John from Lake George, NY
    • Parts Used:
      WE3X75, WE25X60
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Screw drivers, Socket set
    squeaking when drying heavy loads
    Remove 4 screws inside door and swing top back(hinges). Remove front by taking out screws(2) inside top corners and loosen screws(2) at bottom of panel. Swing panel to side of dryer; no need to disconnect any wires. Remove access panel on back of dryer and take off spring clip and washers from end of drum shaft. Pull drum forward about 6 inches(can do this without removing belt) remove old bearing and install new. Reinstall drum. Front slides are a simple remove and replace; helps to have something to hold drum up an inch or 2. Reassemble in reverse order
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      William from Gravois Mills, MO
    • Parts Used:
      WE12X10014, WE25X60
    • Difficulty Level:
      Easy
    • Total Repair Time:
      1- 2 hours
    • Tools:
      Screw drivers, Socket set
    Drive belt broke after 24 years of service
    Disconnect power. Removed four screws from the top of the door opening. These screws have a star pattern and require a star type screw driver. With the four screws removed, lift the front edge of the top and rotate it upward to a vertical position for access to the drum. Locate and remove two screws located at the inside top corners securing the front panel. Disconnect two door switch wires. Loosen, but don't remove the two screws at the front bottom corners of the machine that secure the bottom of the front panel. Lift the front panel up about an inch and rotate the front panel 90 degrees to the right. Using a vacuum, start vacuuming accumulated lint and dirt. Lift the dyer drum up slightly and pull forward. Vacuum and set aside. Vacuum lint and dirt from dryer housing. At the back of the dryer, remove the dryer duct and remove the black panel at the bottom of the housing. Check drum slides at the front of the machine and replace if damaged or worn. Reinstall the dryer drum, draping the new drive belt around the drum prior to engaging the bearing pin at the rear. From the opening at the bottom rear of the machine, tread the drive belt around the motor drive pulley and the tensioner wheel. The portion of the drive belt coming from the left side of the drum (as seen from the rear) must engage the right side of the tensioner wheel before going around the motor drive pulley. This will provide proper drive tension. Re install rear cover and re install the dryer exhaust duct. From the front, re install the front panel and install the two top screws. Then tighten the two bottom screws that were left loose. Re connect the door switch wires. Lower the top and install the four screws at the top of the door opening. Test the dryer operation.
    1 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      Cruz from twentynine palms, CA
    • Parts Used:
      WE3X75, WE25X60, WE12X81
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Pliers, Screw drivers, Socket set
    Broken Belt
    The belt had broken on the dryer and I had purchased a replacement locally. What I found after dissembling the dryer was the drum slides, idler pulley wheel and rear drum bearing were very worn and needed replaced. Each were very easy to remove and replace. Slight challenges were lining up the pulley, reseating the drum with the belt and solving the how the two (belt and pulley) were configured. It did require a second person. Note: Do not drop any parts into the dryer when reassembling. It will require you to start all over.
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      Craig from Lakeland, FL
    • Parts Used:
      WE25X60
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Nutdriver, Screw drivers
    Drum off center and tearing/catching clothes.
    Remove front panel, replace the slides.
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Model Compatibility
      This part works with the following models:
      Fix Number: FIX267600
      Manufacturer Part Number: WE25X60
      Brand
      Model Number
      Description
      Kenmore
      363DDE8109VML
      Dryer
      Kenmore
      363DDE8200GAL
      Dryer
      Kenmore
      363DDE9200GAL
      Dryer
      General Electric
      62150419
      Dryer
      General Electric
      62150429
      Dryer
      General Electric
      62150439
      Dryer
      General Electric
      62170419
      Dryer
      General Electric
      63150419
      Dryer
      General Electric
      63150429
      Dryer
      General Electric
      63150439
      Dryer
      General Electric
      63170419
      Dryer
      General Electric
      64050439
      Dryer
      General Electric
      64058439
      Dryer
      General Electric
      64170419
      Dryer
      General Electric
      65060439
      Dryer
      General Electric
      65068439
      Dryer
      General Electric
      65170419
      Dryer
      General Electric
      65270419
      Dryer
      General Electric
      66050439
      Dryer
      General Electric
      66058439
      Dryer
      General Electric
      66170419
      Dryer
      General Electric
      861-4730-090
      Dryer - GE Dryer Model 861-4730-090 (8614730090, 861 4730 090) Parts
      General Electric
      861-4730-90
      Dryer - GE Dryer Model 861-4730-90 (861473090, 861 4730 90) Parts
      General Electric
      CADE165RAL
      Dryer - Electric
      General Electric
      CADE165SAL
      Dryer - Electric
      General Electric
      CADE165SWH
      Dryer - Electric
      General Electric
      CADG265RAL
      Dryer - Gas
      General Electric
      CADG265RBL
      Dryer - Gas
      General Electric
      CADG265RCL
      Dryer - GE Dryer Model CADG265RCL Parts
      General Electric
      D537E*119
      Dryer