Part Location Diagram of WE12X10014 GE Drive Belt
See part 213 in the diagram
( Grid squares measure 1x1 inch )

Drive Belt

Works With Model BJLR473ET0WW!

Rated by 4 customers 

?

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

?
$31.89
In Stock
Fix Number:
FIX2350043
Manufacturer #:
WE12X10014
Manufactured by:
GE
Works With Model BJLR473ET0WW!

Product Description

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.0 / 5.0, 4 reviews.
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
John from West Elkton, OH
Parts Used:
WE12X10014
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Replacing belt
First watched some you tube videos, to see how to get dryer apart, the one issue I had was getting the belt onto pulley etc. I found if I removed small access panel in back it was a lot easier than trying to reach in from the front as shown in most of the online videos
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Maryland Heights, MO
Parts Used:
WE12X10014
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
belt broke after 38 years
Removed vent pipe pulled it away from the wall. Unplugged it,and ground wire. Opened top and loosened front.installed new belt and figured out tensioner worked (that took time!) and picked up broken belt. Put back together.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Gravois Mills, MO
Parts Used:
WE12X10014, WE25X60
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Drive belt broke after 24 years of service
Disconnect power. Removed four screws from the top of the door opening. These screws have a star pattern and require a star type screw driver. With the four screws removed, lift the front edge of the top and rotate it upward to a vertical position for access to the drum. Locate and remove two screws located at the inside top corners secur ing the front panel. Disconnect two door switch wires. Loosen, but don't remove the two screws at the front bottom corners of the machine that secure the bottom of the front panel. Lift the front panel up about an inch and rotate the front panel 90 degrees to the right. Using a vacuum, start vacuuming accumulated lint and dirt. Lift the dyer drum up slightly and pull forward. Vacuum and set aside. Vacuum lint and dirt from dryer housing. At the back of the dryer, remove the dryer duct and remove the black panel at the bottom of the housing. Check drum slides at the front of the machine and replace if damaged or worn. Reinstall the dryer drum, draping the new drive belt around the drum prior to engaging the bearing pin at the rear. From the opening at the bottom rear of the machine, tread the drive belt around the motor drive pulley and the tensioner wheel. The portion of the drive belt coming from the left side of the drum (as seen from the rear) must engage the right side of the tensioner wheel before going around the motor drive pulley. This will provide proper drive tension. Re install rear cover and re install the dryer exhaust duct. From the front, re install the front panel and install the two top screws. Then tighten the two bottom screws that were left loose. Re connect the door switch wires. Lower the top and install the four screws at the top of the door opening. Test the dryer operation.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Sandyston, NJ
Parts Used:
WE12X10014
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
brocken drum belt
great
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1

Model Compatibility

This part works with the following models:
Fix Number: FIX2350043
Manufacturer Part Number: WE12X10014
Brand
Model Number
Description
Kenmore
363DDE8509RCMA
Dryer - Kenmore Dryer Model 363.DDE8509RCMA (363DDE8509RCMA, 363 DDE8509RCMA) Parts
Kenmore
363DDE8509RCMW
Dryer - Kenmore Dryer Model 363.DDE8509RCMW (363DDE8509RCMW, 363 DDE8509RCMW) Parts
Kenmore
363DDE9600RCMA
Dryer - Kenmore Dryer Model 363.DDE9600RCMA (363DDE9600RCMA, 363 DDE9600RCMA) Parts
General Electric
61140418
Dryer
General Electric
61140419
Dryer
General Electric
61148418
Dryer
General Electric
61148419
Dryer
General Electric
62140418
Dryer
General Electric
62140419
Dryer
General Electric
62148418
Dryer
General Electric
62148419
Dryer
General Electric
62170419
Dryer
General Electric
62180419
Dryer
General Electric
62188419
Dryer
General Electric
62190419
Dryer
General Electric
62190429
Dryer
General Electric
62190439
Dryer
General Electric
62190449
Dryer
General Electric
62190459
Dryer
General Electric
62190479
Dryer
General Electric
62198419
Dryer
General Electric
62198429
Dryer
General Electric
62198439
Dryer
General Electric
62198449
Dryer
General Electric
62198459
Dryer
General Electric
62198479
Dryer
General Electric
63040419
Dryer
General Electric
63040459
Dryer
General Electric
63040479
Dryer
General Electric
63048419
Dryer