Amana Dryer Thrust Washer WP233520 | Fix.com

Thrust Washer

&SeePartX&
Thrust Washer – Part Number: WP233520
https://fixcom.azureedge.net/Schematics/Maytag/4AU3KWVD.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This washer is 3/4 inches in diameter.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Dryer, Washer, Washer Dryer Combo.

Installation Videos

Replacing your Amana Dryer Thrust Washer
Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Fixes the following symptoms:
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • Will not agitate
  • Will not tumble
Tools used for this repair:
  • 5/16ths nut driver
  • E-ring pliers
  • Putty knife

Installation Instructions

Showing 1-6 of 6 Instructions

Cloths still wet after cycle

Take the front panels off, there's 2 screws at the bottom of each panel. Unplug the wire harness from the back of the motor and remove the belt from the pulleys. Pay close attention to the way that the belt runs. It's a little difficult to put back on so you only want to do it once. Disconnect the water hoses from to pump. Put a towel under it a little water will come out. Unbolt the motor and remove it. I replaced the idle pulley and the belt. The pump must be removed from the motor there are 3 torx screws. The idle pulley has to be removed with snap ring pliers. Replace the belt and reassemble. Again pay close attention how the belt goes on in relation to the pump screws. Put the motor back in the washer. Another set of hands would be helpful when bolting it back in, it's awkward and there's very little room. Put the belt back on the pulleys. It's tricky be patient. Hook the hoses back up and plug in the wire harness. I ran a load just to make sure nothing leaked before I put the front panels back on. Having done it once if I had to do it again it would go much easier.

Were these instructions helpful?

3 of 4 people found these instructions helpful
Parts Used: Spin Belt , Thrust Washer
Difficulty Level: A Bit Difficult
Total Repair Time: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Michael from Mount Clemens, MI

Grinding , drum flopping , .....noise !

I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you !

Were these instructions helpful?

2 of 2 people found these instructions helpful
Parts Used: Idler Pulley Wheel with Bearing , High Temperature Adhesive - 2oz. , Idler Pulley Spring , Drum Support Roller and Shaft Assembly , Multi Rib Belt - 93-3/8" , Idler Pulley Lever and Shaft , Cylinder Felt Seal , Retaining Ring , Thrust Washer
Difficulty Level: Really Easy
Total Repair Time: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Ralph from Alexandria, OH

Noisy dryer from an obvious part(s) failure.

Removed eight ?" screws (8A X 3/8 Hex Washer Head Tapping) starting with two at bottom kick panel, then two at dryer door panel; disconnect electrical connectors to release door panel from dryer body; remove four screws from dryer opening bulkhead to expose drum and blower impeller; remove two screws securing top dryer panel to side panels; reach inside right lower access to release dryer belt from idler wheel; lift top panel a little while pulling out bulky drum. Vacuum the heck out of the inside. Even better, do all this outside and take compressed air to the inside. Because this dryer was 19 years old, all three rollers (drum, idler wheel), guides (2), felts(2), and belt were replaced. The noise was caused by seized rollers but all rubber on rollers and belt was cracking, so best to change such old worn out parts. Don't forget to lube all shafts with oil (plumbers silicone best), then reassemble...js

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Single Felt Pad , Multi Rib Belt - 93-3/8" , Drum Glide , Drum Support Roller - for square ported models , Retaining Ring , Thrust Washer
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver
Customer: Joseph from Tucson, AZ

Noisy when operating

followed instructions in vidios for belt and idler pulley and tub support rollers model in vidios different but came apart basicly the same way. dryer is 17 yrs old, glad to find parts runs quiet as new idler pulley and shaft not worn replaced anyway only belt and left hand tub support roller and shaft were worn

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Wheel with Bearing , Drum Support Roller and Shaft Assembly , Multi Rib Belt - 93-3/8" , Drum Glide , Idler Pulley Lever and Shaft , Drum Support Roller - for square ported models , Single Drum Glide Felt Pad , Thrust Washer
Difficulty Level: Easy
Total Repair Time: 1- 2 hours
Tools: Nutdriver, Socket set
Customer: reginald from mount holly, NJ

Bearing on belt tension pulley wore out.

took front two pieces off to gain access to pulley and bracket. took bracket off with 7/16 socket. installed new pulley and bracket. installed new belt over tub. put front back on except bottom panel. installed belt on to new pulley . replaced bottom panel.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Idler Pulley Wheel with Bearing , Multi Rib Belt - 93-3/8" , Idler Pulley Lever and Shaft , Thrust Washer
Difficulty Level: Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver, Socket set
Customer: dan from marion, IN

Clothes where getting holes from getting caught on edge of the drum

I took the face off the dryer then removed the drum. Inspected the dryer for broken parts because I already knew the drum glide was damaged that's why my clothes where getting caught on the edge of the drum and getting damaged.I replaced all the parts that I found very easily on the site ,with the picture diagrams that come up to choose parts you need is very simple to see what exact parts you need to replace on your appliances. And my dryer has been working ever since. Thanks

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Single Felt Pad , Multi Rib Belt - 93-3/8" , Drum Glide , Glide Bracket Kit , Thrust Washer
Difficulty Level: Easy
Total Repair Time: 1- 2 hours
Tools: Screw drivers, Socket set
Customer: Jesus from philadelphia, PA
Showing 1-6 of 6 Instructions

Model Cross Reference List

This part works with the following models:

Fix Number: FIX11740482
Manufacturer Part Number: WP233520


Brand
Model Number
Description
Kenmore
10687884100
Dryer
Kenmore
10687884300
Dryer
Kenmore
10687884600
Dryer
Kenmore
11051730
Washer
Kenmore
11055594
Washer
Kenmore
1105807410
Dryer
Kenmore
1105808010
Dryer
Kenmore
1105808700
Dryer
Kenmore
1105808800
Dryer
Kenmore
1105808810
Dryer
Kenmore
1105808850
Dryer
Kenmore
1105808860
Dryer
Kenmore
1105817820
Dryer
Kenmore
1105817830
Dryer
Kenmore
1105818810
Dryer
Kenmore
1105818820
Dryer
Kenmore
1105907000
Dryer
Kenmore
1105907100
Dryer
Kenmore
1105907400
Dryer
Kenmore
1105907500
Dryer
Kenmore
1105907501
Dryer
Kenmore
1105907600
Dryer
Kenmore
1105907610
Dryer
Kenmore
1105907700
Dryer
Kenmore
1105907710
Dryer
Kenmore
1105907720
Dryer
Kenmore
1105907721
Dryer
Kenmore
1105907730
Dryer
Kenmore
1105907800
Dryer
Kenmore
1105907801
Dryer