Maytag/Maytag_Thumb/4AU3KWVD.gif
See part 18 in the diagram
Replacing your Amana Dryer Thrust Washer play video
( Grid squares measure 1x1 inch )

Thrust Washer

$7.76
Fix Number: FIX11740482
Manufacturer #: WP233520
Manufactured by: Whirlpool

Product Description

This washer is 3/4 inches in diameter.

Videos For installing this part.

Replacing your Thrust Washer

Replacing your Thrust Washer play video
Questions and Answers

Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leslie
November 29, 2022
My dryer started making a loud squeeking grinding noise when I turn it on which lasts only a few seconds and otherwise sounds normal runing. Only at the begining. Ive looked everywhere in your repair advice and cant find a suggestion. Can you tell me what part(s) you think may be the source of this problem, which I need to purchase and install?
For model number LE8317w2
Hi Leslie, thank you for reaching out. The following parts need to be checked to fix the issue: Drive Belt, part number FIX11742271, and Drum Support Roller, part number FIX11741913. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.

Was this helpful?
Thank you for voting!
Related Parts:

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 2.8 / 5.0, 6 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Grinding , drum flopping , .....Noise !
I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you !
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Michael from Mount Clemens, MI
  • Parts Used:
    WP27001007, WP233520
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Cloths still wet after cycle
Take the front panels off, there's 2 screws at the bottom of each panel. Unplug the wire harness from the back of the motor and remove the belt from the pulleys. Pay close attention to the way that the belt runs. It's a little difficult to put back on so you only want to do it once. Disconnect the water hoses from to pump. Put a towel under it a little water will come out. Unbolt the motor and remove it. I replaced the idle pulley and the belt. The pump must be removed from the motor there are 3 torx screws. The idle pulley has to be removed with snap ring pliers. Replace the belt and reassemble. Again pay close attention how the belt goes on in relation to the pump screws. Put the motor back in the washer. Another set of hands would be helpful when bolting it back in, it's awkward and there's very little room. Put the belt back on the pulleys. It's tricky be patient. Hook the hoses back up and plug in the wire harness. I ran a load just to make sure nothing leaked before I put the front panels back on. Having done it once if I had to do it again it would go much easier.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy dryer from an obvious part(s) failure.
Removed eight ?" screws (8A X 3/8 Hex Washer Head Tapping) starting with two at bottom kick panel, then two at dryer door panel; disconnect electrical connectors to release door panel from dryer body; remove four screws from dryer opening bulkhead to expose drum and blower impeller; remove two screws securing top dryer panel to side panels; reach inside right lower access to release dryer belt from idler wheel; lift top panel a little while pulling out bulky drum. Vacuum the heck out of the inside. Even better, do all this outside and take compressed air to the inside. Because this dryer was 19 years old, all three rollers (drum, idler wheel), guides (2), felts(2), and belt were replaced. The noise was caused by seized rollers but all rubber on rollers and belt was cracking, so best to change such old worn out parts. Don't forget to lube all shafts with oil (plumbers silicone best), then reassemble...js
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noisy when operating
followed instructions in vidios for belt and idler pulley and tub support rollers model in vidios different but came apart basicly the same way. dryer is 17 yrs old, glad to find parts runs quiet as new idler pulley and shaft not worn replaced anyway only belt and left hand tub support roller and shaft were worn
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bearing on belt tension pulley wore out.
took front two pieces off to gain access to pulley and bracket. took bracket off with 7/16 socket. installed new pulley and bracket. installed new belt over tub. put front back on except bottom panel. installed belt on to new pulley . replaced bottom panel.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clothes where getting holes from getting caught on edge of the drum
I took the face off the dryer then removed the drum. Inspected the dryer for broken parts because I already knew the drum glide was damaged that's why my clothes where getting caught on the edge of the drum and getting damaged.I replaced all the parts that I found very easily on the site ,with the picture diagrams that come up to choose parts you need is very simple to see what exact parts you need to replace on your appliances. And my dryer has been working ever since. Thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX11740482
Manufacturer Part Number: WP233520
Brand
Model Number
Description
Kenmore
10687884100
Dryer
Kenmore
10687884300
Dryer
Kenmore
10687884600
Dryer
Kenmore
10697502820
Dryer - Kenmore Dryer Model 106.97502820 (10697502820, 106 97502820) Parts
Kenmore
11051730
Washer
Kenmore
11055594
Washer
Kenmore
1105807410
Dryer
Kenmore
1105808010
Dryer
Kenmore
1105808700
Dryer
Kenmore
1105808800
Dryer
Kenmore
1105808810
Dryer
Kenmore
1105808850
Dryer
Kenmore
1105808860
Dryer
Kenmore
1105817820
Dryer
Kenmore
1105817830
Dryer
Kenmore
1105818810
Dryer
Kenmore
1105818820
Dryer
Kenmore
1105907000
Dryer
Kenmore
1105907100
Dryer
Kenmore
1105907400
Dryer
Kenmore
1105907500
Dryer
Kenmore
1105907501
Dryer
Kenmore
1105907600
Dryer
Kenmore
1105907610
Dryer
Kenmore
1105907700
Dryer
Kenmore
1105907710
Dryer
Kenmore
1105907720
Dryer
Kenmore
1105907721
Dryer
Kenmore
1105907730
Dryer
Kenmore
1105907800
Dryer