See part 10 in the diagram
( Grid squares measure 1x1 inch )
Door Switches and Holder Assembly
$
44.54
In Stock
In Stock
Fix Number: FIX2099645
Manufacturer #: 99002254
Manufactured by:
Whirlpool
-
Product Description
This part senses when the door is closed so the cycle can start.
-
Works with the following brandsMaytag, Jenn-Air, Magic Chef, Crosley
-
Works with the following productsDishwasher
-
Fixes the following symptomsWill Not Start, Door latch failure, Door won’t close
-
Part Number Cross ReferencePart# 99002254 replaces these:AP4113223, 780069, 9-3086, 903086, 99001077, 99002254
Product Description
This part senses when the door is closed so the cycle can start.
-
Works with the following brands:Maytag, Jenn-Air, Magic Chef, Crosley
-
Works with the following products:Dishwasher
-
Fixes the following symptoms:Will Not Start, Door latch failure, Door won’t close
-
Part# 99002254 replaces these:AP4113223, 780069, 9-3086, 903086, 99001077, 99002254
Videos For installing this part.
Installation Instructions Provided by Fix customers like you.
Average Repair Rating: 3.9 / 5.0, 4 reviews.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:WILLIAM from SHEPHERDSVILLE, KY -
Parts Used:99002254 -
Difficulty Level:Really Easy -
Total Repair Time:30 - 60 mins -
Tools:Pliers, Screw drivers
Dishwasher stops during wash cycle - push in on door latch and it resumes
I followed the installation video. First turned off the circuit breaker. Removed the door panel, black shield, and wires. Separated the latch handle from the holder assembly. Inserted the latch handle into the new holder assembly. Put the new switches in the holder assembly, reconnected the wires, snapped on the black shield, and screwed the door panel back on. Turned on the breaker. The dishwasher would not start, and I could hear the switches clicking when I pushed on the door. So I repeated the whole process making sure I had the handle and holder assembly fully seated and lined up with the screw holes. That did the trick. I've run 3 loads since, and the dishwasher completed the wash cycle every time. This site is the best!
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Connie from Oakland, CA
-
Parts Used:99002254
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Dishwasher would not start
Followed the video provided by this site. Since we discovered this was a 1995 Model we weren't sure fix would work, but thought it was worth a try....and it worked!!! Dishwasher started right up. Thank You!!!!!
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Patrick from Cabin John, MD
-
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:
Dishwasher would not stay running; pushing on door would actuate power.
No go without a torx driver. There are 8 screws to remove and 7 are torx. A power driver makes the job much faster. Remove the plastic door liner without disconnecting the wiring. 7 screws. Remove the Philips screw that holds the switch housing. Set your drill on the inside of the door otherwise the door spring tension will slam the door shut on you. If you only ordered the switch itself, be very careful not to break off the switch retaining clip from the switch housing. It is easy to break. Pull the leads off of the switch, put them on the new switch, and push it back in to the housing. Remount the housing and re-screw, being careful to put it on the correct (indented) side. Lay the panel back in and re-screw it.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:James from Teaneck, NJ
-
Parts Used:99002254
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Dishwasher door switch
I followed your video which was very detailed and easy. However, I broke a part of the switch when trying to put it back in the door. Fortunately I was able to clean the corrosion off of one of the old switches to replace the new switch. The lock works perfectly. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX2099645
Manufacturer Part Number: 99002254
Manufacturer Part Number: 99002254
Brand
Model Number
Description