GE/GE_Thumb/00124321i02.gif
See part 744 in the diagram
Replacing your General Electric Dishwasher Water Inlet Valve play video
( Grid squares measure 1x1 inch )

Water Inlet Valve

$41.83
Fix Number: FIX3654179
Manufacturer #: WD15X10014
Manufactured by: GE

Product Description

This water inlet valve is an authentic OEM part for your dishwasher. If can be found behind the lower kickplate panel in either the left or right corner. The valve has a solenoid that opens or closes in order to provide the required amount of water. If your dishwasher is leaking or will not fill with water, you may need to replace the water inlet valve.

Videos For installing this part.

Replacing your Water Inlet Valve

Replacing your Water Inlet Valve play video
Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.3 / 5.0, 6 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
  • Customer:
    Walter from Rochester, NY
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set, Wrench set
Leaking valve
Turn off electrical power and water supply. 1. Remove floor access plate, 2.disconnect wire clip blocking right mounting screw being sure to depress release clip in the body of the clip, 3. remove 2 mounting screws using 5/16 open-end wrench, 4.Using needle nose pliers, move spring clip on water discharge hose away from valve body, 5. remove discharge hose, 6. pull valve assembly from under dishwasher, 7. disconnect second electrical contact from the side of the inlet valve,.8. remove water inlet hose from the valve and discard valve. Reverse this procedure for installation of new water inlet valve.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Brian from Wyomissing, PA
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
Water leak under dishwasher
Removed dishwasher kick panel after removing 2 screws. Removed 2 screws holding top of dishwasher in place (at top front of dishwasher in counter or top sides of dishwasher). Pulled dishwasher forward slightly to get better access. Using small wrench, removed 2 sheet metal screws holding inlet assembly to dishwasher. Disconnected electric connector to part. Disconnected water supply with wrench. Disconnected water outlet connection using pliers to move retaining band out of way and then pulled off connecting tube. In removed assembly, used wrench to remove 90 degree inlet adapter. Installed new Teflon tape on inlet adapter and installed in new part. Reversed disassembly procedure to complete installation of new part.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    C. J. from Morristown, AZ
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
Machine was not filling with water
Your probability analysis was on the money. (75% of the time it is the water inlet valve). The fix was pretty easy - pull the machine from under the counter, find the valve, replace same, push it back under the counter, wash some dishes. I have some aptitude and some common sense, but this was really pretty easy and quick. Advice to the less qualified: make sure you have all the right tools and take your time...... Call your brother in law as a last resort.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Robert from Billings, MT
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Slow leak. Dirty dishes.
Saw the leak. Looked up the part. Part came 3 days later. Fixed in time from Christmas
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Jack from Holland, PA
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
LEAK UNDER THE DISHWASHER
UNSCREWED THE BOTTOM FRONT SKIRT OFF BY USING A NUT DRIVER. FOUND THE WATER INLET VALVE DRIPPING. PULLED THE SELONOID CONNECTION APART...A BIT HARD SO WIGGLE IT LOOSE. SHUT THE WATER VALVE OFF TO THE DISHWASHER. USED A NUT DRIVER TO UN-SCREW THE TWO SCREWS HOLDING THE ENTIRE WATER INLET VALVE / ASSEMBLY BRACKET. TRICKY TO GET THE RIGHT SCREW OUT. IT'S BEHIND ANOTHER SMALL ELECTRICAL CONNECTOR. BEST TO PULL THAT ONE APART AS WELL OR DO WHAT I DID, USE A NUT DRIVER HOLDER WITH A SMALL SOCKET AND DO NOT PUT THE SOCKET ALL THE WAY ONTO THE DRIVER. THIS WILL ALLOW THE SOCKET TO GO OVER THE HEX SCREW HEAD ON AN ANGLE SO YOU CAN LOOSEN THIS SCREW. THE ASSEMBLY WILL THEN DROP DOWN. USE A LONG (10" LONG) NEEDLE NOSE PLIER TO SQUEEZE THE RUBBER HOSE ATTACHEMENT CLIP APART THEN PUSH IT BACK OFF THE TIP OF THE HOSE NOZZLE ADAPTER. NOW GRAB THE HOSE AND VALVE ASSEMBLY AND GIVE IT A GOOD HARD PULL SEPERATE THE RUBBER HOSE OFF THE ASSEMBLY...VOILA YOU HAVE THE LEAKY VALVE OFF. RECONNECT THE NEW UNIT IN THE SAME WAY AS YOU TOOK OUT THE OLD. TIP...MARK THE OLD WITH A MARKER SO YOU DON'T ACCIDENTALLY PUT THE OLD ONE BACK...THEY LOOK THE SAME. THIS IS DONE WITHOUT PULLING THE MACHINE OUT FROM UNDER THE COUNTER TOP. NOT HARD TO DO, JUST TIGHT SPACE TO WORK WITH.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Peter from Naples, FL
  • Parts Used:
    WD15X10014
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
water leak on floor
Remove bottom panel, remove 2 screws that hold valve that makes the parts to be removed easer to get at take off 2wires ,disconnect 3/8 water suply and with a small pair of channel lock pliers remove water outlet clamp. Install new water valve in reverse
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX3654179
Manufacturer Part Number: WD15X10014
Brand
Model Number
Description
General Electric
ADW1100N00BB
Dishwasher
General Electric
ADW1100N00WW
Dishwasher
General Electric
ADW1100N10BB
Dishwasher
General Electric
ADW1100N10WW
Dishwasher
General Electric
ADW1100N15BB
Dishwasher
General Electric
ADW1100N15WW
Dishwasher
General Electric
ADW1100N20BB
Dishwasher
General Electric
ADW1100N20WW
Dishwasher
General Electric
ADW1100N30BB
Dishwasher
General Electric
ADW1100N30WW
Dishwasher
General Electric
ADW1100N35BB
Dishwasher
General Electric
ADW1100N35WW
Dishwasher
General Electric
ADW1100NB
Dishwasher - GE Dishwasher Model ADW1100NB Parts
General Electric
ADW1100NW
Dishwasher - GE Dishwasher Model ADW1100NW Parts
General Electric
CDW9380N00SS
Dishwasher - GE CAFE
General Electric
CDW9380N20SS
Dishwasher
General Electric
CDWT280V00SS
Dishwasher
General Electric
CDWT280V05SS
Dishwasher
General Electric
CDWT280V50SS
Dishwasher
General Electric
CDWT980R10SS
Dishwasher
General Electric
CDWT980R30SS
Dishwasher
General Electric
CDWT980V00SS
Dishwasher
General Electric
CDWT980V05SS
Dishwasher
General Electric
CDWT980V50SS
Dishwasher
General Electric
EDWF800P00BB
Dishwasher
General Electric
EDWF800P00WW
Dishwasher
General Electric
EDWF860P00SS
Dishwasher
General Electric
GDWF100R10BB
Dishwasher
General Electric
GDWF100R10WW
Dishwasher
General Electric
GDWF100R30BB
Dishwasher