This dishwasher door gasket is attached to the bottom of the door, creating a strong seal between the tub and the outer edge of the door. This seal is prone to wear and tear due to its constant exposure to water, detergent, and food particles. If the gasket appears cracked, broken, or you notice a leak coming from the door, it will need to be replaced immediately. This gasket measures approximately 23 inches long. For this simple repair, no tools are necessary. Open the dishwasher door and remove the bottom rack. The gasket is located right along the bottom of the door, molded inside the channel. It is held in place in the groove across the bottom. Remove the old gasket by pulling it out with your hands. Take your new silicone gasket and line it up so the notch fits into the groove and slide it in place until it is secure. Reinstall the lower dishrack. We recommend leaving the door closed for a few hours to ensure the gasket is sealed tightly.
Works with the following brands:
Frigidaire, Kenmore, Crosley, Gibson
Works with the following products:
Dishwasher
Fixes the following symptoms:
Leaking, Not cleaning dishes properly, Door won’t close, Door latch failure
Part# 809006501 replaces these:
AP5809675, 154297601, 154297602, 154297603, 154576501, 154588201
...
Show more, 154759101 Show less
Works with the following brands:
Frigidaire, Kenmore, Crosley, Gibson
Works with the following products
Dishwasher
Fixes the following symptoms
Leaking, Not cleaning dishes properly, Door won’t close, Door latch failure
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Maureen
August 18, 2022
when I put in the lower door seal in it goes right thru the channel..everything lines up just fine..it just falls right thru..any help...?
For model number FDB1050REC0
Hello Maureen, Thank you for the question. We suggest checking the Channel that the gasket slides into and check to make sure it is not warped and able to hold the gasket in place. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Peg
January 19, 2022
Good for model FGHD2465NF1A. Serial Th41755345 Frigidaire Gallery
For model number FGHD2465NF1A
Hello Peg, Thank you for contacting us. We have researched the model you have provided and can confirm the part you are looking for is Fix Number: FIX9495545. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jon
February 15, 2022
Bottom dishwasher door seal...parts don't look like mine
For model number 665 .13223n414
Hi Jon,
Thank you for your question. The part number listed under your model number for the lower door seal is FIX11766757. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
I replaced the bottom door seal but the seal doesn’t stay when opening and closing the door
For model number FRIG2466QFA
Hi Dan, thank you for contacting us. If dirt or debris is preventing your dishwasher door seal from sealing properly, we suggest that you clean it thoroughly. Use warm soapy water and a soft cloth to wipe the seal and the surface and put the seal back. We hope this helps!
Was this helpful?
Thank you for voting!
John
December 8, 2023
will DU930pwpb2 bottom dishwasher door gasket inter change with replacement part 809006501 or what numbers gasket ?
For model number DU930pwpb2
Hi John,
Thank you for your question. There is no bottom door gasket listed for your dishwasher. If water is leaking from the bottom left or right corners of the door, you will need to replace the door gasket, part number FIX11755809. We hope this helps!
Hello Jerry, Thank you for your inquiry. We have researched the model number you have provided and show that the bottom door seal is only available as part of the inner door panel. We hope this helps.
The door gasket provides a watertight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. This gray door gasket is ...
If your dishwasher is leaking from the corners of the gasket, you may need to replace the splash shields. The splash shields attach to the lower front corners of dishwasher and are used to prevent water from escaping pas...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
I ordered the top 3 parts in terms of probability of solving the problem (water inlet valve, tub gasket, and bottom door gasket). I installed all 3 and it did not solve the door leak. Then I realized that the bottom door gasket had come out (in other words, I had not installed it properly). I reinstalled the bottom door gasket (a criti
... Read morecal point is that it has to be *pressed in* firmly -- there should be some resistance), and it worked. Note that the bottom door gasket is a hybrid between a true seal and a splash guard. The notch in the middle is designed to drain water from the door back into the tub. Because of that notch opening, there is sputtering and splashing at various points of the wash cycle. This appears to be by design, and those splashes result in water being absorbed by the insulating foam. Thank you to the previous submission/posting authors, as this is what clued me in.
Opened plastic package with scissors. Opened door of dish washer. At bottom of door pulled gripped old gasket seal with plyers and pulled it out of slot. Pushed new gasket in place...too long. Marked extra length with sharpy black pen and removed gasket. Cut gasket with scissors and pushed it into slot. Fit perfect. Note slot us under lip
... Read more of door, a little tricky to find in order to install. Works great, no more leak.Make sure you use a screw driver on the door screws to make sure they are all tight. Too seal them use Blue Lock tight sealer.
The old gasket was easy to pull out. I didn't get the new one in straight the first time and closing the door was difficult. The new gasket popped out and I got it lined up better and pushed it back in. Tested the seal by running the rinse cycle and no leaking!
I watched the video that you provided and I proceeded to follow the directions and install the gasket. Very easy once my husband stopped interfering.However , the bad news was that the leak was not fixed. There is a much bigger leak that seems to spray water from somewhere on the bottom, towards the center/rear of the machine. I can't get
... Read more a handle on the exact part without pulling the entire machine out, which is complicated because of the manner in which it was installed. So, if I decide to take it on, I will most definitely be calling upon your fantastic customer service. Thank you. Sincerely, Noreen
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.