Watch the install video
1990907-1-M-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz
Part Location Diagram of 154637401 Frigidaire Water Inlet Valve - 120V 60Hz
See part F3 in the diagram
Replacing your Frigidaire Dishwasher Water Inlet Valve - 120V 60Hz
1990907-1-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 360 view
( Grid squares measure 1x1 inch )
1990907-1-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 1990907-2-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 1990907-1-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 360 view
Part Location Diagram of 154637401 Frigidaire Water Inlet Valve - 120V 60Hz Replacing your Frigidaire Dishwasher Water Inlet Valve - 120V 60Hz

Water Inlet Valve - 120V 60Hz

Works With Model FDB1051REB2!

Rated by 16 customers 

?

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

?
$57.03
In Stock
Fix Number: FIX1990907
Manufacturer #: 154637401
Manufactured by: Frigidaire
Works With Model FDB1051REB2!
  • Product Description

    This is a genuine OEM replacement water inlet valve for your dishwasher. The water inlet valve supplies water to the dishwasher by opening and closing the solenoids attached to the valve, depending on the desired quantity of water. If your dishwasher is overfilling and leaking, or not filling with water at all, these may be signs that your valve is faulty. Other symptoms can include your dishes not cleaning properly, and the dishwasher not draining. You can check the inlet valve for continuity with a multimeter. It should show a reading between 500 - 1500 ohms if the valve is working and will read infinity if it is faulty. Another test is to open the dishwasher door while it is filling. If the tub continues to fill with water when the door is opened, the water inlet valve is defective and should be replaced.

  • Works with the following brands
    Frigidaire, Kenmore, Crosley, Gibson
  • Works with the following products
    Dishwasher
  • Fixes the following symptoms
    Leaking, Will not fill with water, Not cleaning dishes properly, Not draining
  • Part Number Cross Reference
    Part# 154637401 replaces these:
    AP4321824, 1378823, 154637401, 154219601, 154219602, 154359801, 154359802, 154373301, 154373303, 154445901, 154476101
1 Installation Video Questions and Answers
16 Installation Instructions Model Compatibility
Product Description Part Videos Questions and Answers Installation Instructions Model Compatibility

Product Description

This is a genuine OEM replacement water inlet valve for your dishwasher. The water inlet valve supplies water to the dishwasher by opening and closing the solenoids attached to the valve, depending on the desired quantity of water. If your dishwasher is overfilling and leaking, or not filling with water at all, these may be signs that your valve is faulty. Other symptoms can include your dishes not cleaning properly, and the dishwasher not draining. You can check the inlet valve for continuity with a multimeter. It should show a reading between 500 - 1500 ohms if the valve is working and will read infinity if it is faulty. Another test is to open the dishwasher door while it is filling. If the tub continues to fill with water when the door is opened, the water inlet valve is defective and should be replaced.

  • Works with the following brands:
    Frigidaire, Kenmore, Crosley, Gibson
  • Works with the following products:
    Dishwasher
  • Fixes the following symptoms:
    Leaking, Will not fill with water, Not cleaning dishes properly, Not draining
  • Part# 154637401 replaces these:
    AP4321824, 1378823, 154637401, 154219601, 154219602, 154359801 ... Show more , 154359802, 154373301, 154373303, 154445901, 154476101 Show less

Videos For installing this part.

Replacing your Water Inlet Valve - 120V 60Hz

Replacing your Water Inlet Valve - 120V 60Hz

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.8 / 5.0, 16 reviews.
  • 1
  • 2
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
  • Customer:
    Patrick from Pleasanton, CA
  • Parts Used:
    809006501, 154827601, 154637401
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
leak from door
I ordered the top 3 parts in terms of probability of solving the problem (water inlet valve, tub gasket, and bottom door gasket). I installed all 3 and it did not solve the door leak. Then I realized that the bottom door gasket had come out (in other words, I had not installed it properly). I reinstalled the bottom door gasket (a critical point is that it has to be *pressed in* firmly -- there should be some resistance), and it worked. Note that the bottom door gasket is a hybrid between a true seal and a splash guard. The notch in the middle is designed to drain water from the door back into the tub. Because of that notch opening, there is sputtering and splashing at various points of the wash cycle. This appears to be by design, and those splashes result in water being absorbed by the insulating foam. Thank you to the previous submission/posting authors, as this is what clued me in.
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Robert from Copiague, NY
  • Parts Used:
    154637401, 5300809640
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Stalled Timer, dirty dishes, detergent wasn't dissolving properly.
At first I thought the Timer was bad because it was stalling. The Timer only malfunctioned in High Temp Wash or High Temp Rinse mode. After removing and checking the timer, I determined it was working OK. Someone mentioned that a bad thermostat could cause the Timer to stall, but I wasn't having any problems with hot water temperature. I noticed the detergent wasn't dissolving completely, and the water flowing into the tub sounded weak, so I replaced the water inlet valve. This solved all my problems. Dishes are coming out sparkling clean and the Timer doesn't stall in High Temp mode. I just followed the video on Part Select to make the repair. I didn't pull out the whole dishwasher from the counter and I removed the Lower Door panel in addition to the Kick Plate. Removing the Lower Door Panel provided easier access to the valve. I hope this helps other people troubleshoot their dishwasher. Once again this site saved me a chunk of money.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    James from Aberdeen, WA
  • Parts Used:
    154637401
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
the water inlet valve was leaking at the solenoid.
I cut off the power and the water. Then I opened the door and removed the two screws up top anchoring it to the counter. Next i pulled it far enough out of its niche (a little over a foot) that I could get at the valve from the side easily. I've done several of these before and find that, while it's possible to change them working strictly from the front, it's actually quicker and much easier to pull them out a bit. Then I removed the kick panel, (two more screws) and slid a small shallow pan underneath the pump to catch the water. Next, I pulled the electrical clip off the solenoid. I used open end wrenches to unscrew the supply hose and pliers to loosen the spring clamp on the fill tube and slide it out past the end of the outlet nipple. The tube stuck a little bit but was not hard to twist off by hand. Finally, I removed the two screws holding the valve to the frame and pulled it out. I screwed the new valve into place and attached everything in the opposite order I took them off. The nipple for the fill tube came out of the new valve at a different angle from the old one so I had to adjust the tube a little. I turned on the water and power and checked for leeks. Then I put it back in its hole.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Allen from Linthicum Heights, MD
  • Parts Used:
    154637401
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve had a slow leak. Needed replacing.
Turn off water supply. Remove inlet hose. Remove front kick plate. Remove filler tube. Remove screws securing water inlet valve. Remove electrical connector from water inlet valve. Reverse procedure with new water inlet valve. Turn water supply on. Check for leaks. Success.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Kenneth from Clermont, FL
  • Parts Used:
    154637401
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
Water Valve was leaking
Just took out the old and replaced with the new. It's in front of the appliance, on the bottom, so it was easy to get to. Just like your video demonstrated.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    James from Shortsville, NY
  • Parts Used:
    154637401
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers
Inlet valve leaking
Had to move dishwasher out to replace the supply line (didn't have a separate shutoff or a union). After that was out of the way it took me less than ten minutes to replace the valve. If you have to do it this way-don't forget to turn off the electric power. Otherwise it's a piece of cake to do.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    shari from hawaiian gardens, CA
  • Parts Used:
    154637401
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Wrench (Adjustable)
no water coming into diswasher
My son helped me flip the dishwasher on its side. I unscrewed the bolts on side of water inlet value, unscrewed the water hose and another hose. put in new water inlet value and reattached other hose, turned dishwasher on and YES I could here the water in the dishwasher. I went one step further and opened dishwasher to make sure it was really water spraying in there and again YES it was. I was so happy I fixed my dishwasher without paying hundreds of dollars for a repair person or buying a new dishwasher, It cost me a whopping $25.18 to fix not including shipping cost.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Steve from North Myrtle Beach, SC
  • Parts Used:
    154844101, 154637401
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher was making a high pitched noise in the wash cycle as well as filling with water when it was off
Just disconnect the power plug, shut off the water supply, disconnect the supply and drain hoses removed the two screws anchoring the unit and slid it out. I laid it on its side and the repairs were simple. The motor comes out after a little twisting to unseat the seal. Be sure to lube the new o-rings with a little dishsoap and it will go in easy. The water inlet valve was very easy to replace, no instructions necessary.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    RICHARD from PEACHTREE CITY, GA
  • Parts Used:
    154637401
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
low inlet water supply
replaced water inlet valve
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Larry from Tower City, PA
  • Parts Used:
    154637401
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Dishwasher would not fill with water
Basically, I found the online video on the website to be a great tool. Followed the instructions, and everything went together perfectly.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Model Compatibility
This part works with the following models:
Fix Number: FIX1990907
Manufacturer Part Number: 154637401
Brand
Model Number
Description
Kenmore
58714001990
Dishwasher
Kenmore
58714001991
Dishwasher
Kenmore
58714002990
Dishwasher
Kenmore
58714012407A
Dishwasher - DISHWASHER
Kenmore
58714012408A
Dishwasher - DISHWASHER
Kenmore
58714012409B
Dishwasher - DISHWASHER
Kenmore
58714012410B
Dishwasher - DISHWASHER
Kenmore
58714012411B
Dishwasher - DISHWASHER
Kenmore
58714012412B
Dishwasher - DISHWASHER
Kenmore
58714013401
Dishwasher
Kenmore
58714013408A
Dishwasher - DISHWASHER
Kenmore
58714013409A
Dishwasher - DISHWASHER
Kenmore
58714013410B
Dishwasher - DISHWASHER
Kenmore
58714013411B
Dishwasher - DISHWASHER
Kenmore
58714013412B
Dishwasher - DISHWASHER
Kenmore
58714013413B
Dishwasher - DISHWASHER
Kenmore
58714014407A
Dishwasher - DISHWASHER
Kenmore
58714014408A
Dishwasher - DISHWASHER
Kenmore
58714014409B
Dishwasher - DISHWASHER
Kenmore
58714014410B
Dishwasher - DISHWASHER
Kenmore
58714014411B
Dishwasher - DISHWASHER
Kenmore
58714014412B
Dishwasher - DISHWASHER
Kenmore
58714019406A
Dishwasher
Kenmore
58714019407A
Dishwasher - DISHWASHER
Kenmore
58714019408A
Dishwasher - DISHWASHER
Kenmore
58714019409B
Dishwasher - DISHWASHER
Kenmore
58714019410B
Dishwasher - DISHWASHER
Kenmore
58714019411B
Dishwasher - DISHWASHER
Kenmore
58714019412B
Dishwasher - DISHWASHER
Kenmore
58714022200A
Dishwasher - DISHWASHER