Roper Dryer Thermostats

★★★★★

★★★★★

15 Reviews

Fix Number

FIX11741460

Manufacturer Part Number

WP3392519

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX11741405

Manufacturer Part Number

WP3387134

This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX334299

Manufacturer Part Number

279816

This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.

★★★★★

★★★★★

1 Review

Fix Number

FIX11742185

Manufacturer Part Number

WP3977767

This is a manufacturer-approved high-limit thermostat for your dryer. This part includes one high limit thermostat with a terminal extension arm. It is a safety mechanism that prevents your dryer from overheating. Once the temperature reaches 221 degrees Fahrenheit, this element will shut down power to the heating element until it decreases to 80 degrees Fahrenheit. If this part is faulty, your dryer may not heat. You will find this part located underneath the dryer vent behind the appliance. The terminal extension arm connects to the heater element terminal. The high limit thermostat can be tested with a multimeter. It should be tested while it is at room temperature, and will need to be replaced if the reading determines it is faulty.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334278

Manufacturer Part Number

279769

This genuine OEM kit includes a high limit thermostat and a thermal cut-off fuse for your dryer. The thermostat has a limit of 250 degrees Fahrenheit, and the fuse has a limit of 360 degrees Fahrenheit. The purpose of these parts is to prevent your dryer from overheating. If your clothes are coming out of the dryer too hot, or there is no heat at all, it is likely that these parts will need to be replaced. To complete this repair, you will need a putty knife, quarter-inch nut driver, and a pair of pliers. Please be sure to disconnect the power supply to your dryer before beginning this repair. The thermostats are located on the element housing, and we find it easiest to remove the entire heating assembly from the dryer in order to replace these parts. Take note when removing the old thermostats, if there is any discoloration on the terminals then the wire ends may also need to be replaced.

Fix Number

FIX11743793

Manufacturer Part Number

WP694674

Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.

Fix Number

FIX11741441

Manufacturer Part Number

WP3390291

With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 250 degrees Fahrenheit. The element will kick back in when the temperature drops to 190 degrees Fahrenheit. Differential of 60 degrees.

Fix Number

FIX11741495

Manufacturer Part Number

WP3398128

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 145 degrees Fahrenheit and a differential of 20 degrees. Meaning that with this thermostat, the heating element will cut out at 145 degrees and cycle back on once the internal temperature drops by 20 degrees.

Fix Number

FIX11741452

Manufacturer Part Number

WP3391381