Models
>
B9757X1
B9757X1 Roper Wall Oven
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for B9757X1
Viewing 6 of 6Manuals & Guides for B9757X1
Click to downloadKeep searches simple, eg. "belt" or "pump".
$13.60
This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.
In Stock
Order within the next 5 hrs and your part ships today!
$92.06
This broil element is found on the roof of the oven and has push-on terminals.
In Stock
Order within the next 5 hrs and your part ships today!
This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.
No Longer Available
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for B9757X1
Viewing 7 of 7Noisy
Fixed by these parts
How to fix it
Little to no heat when baking
Fixed by these parts
How to fix it
Little to no heat when broiling
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Oven not heating evenly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Brecksville, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the strin
... Read more
g still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starla from Vashon, WA
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt out broiler element
Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Mill Valley, CA
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler wouldn't heat
First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.
Was this instruction helpful to you?
Thank you for voting!