Models > LRE30755ST > Instructions

LRE30755ST ((ASTELGA)) LG Range - Instructions

Jump to:

All Instructions for the LRE30755ST
1 - 5 of 5
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeffrey from CERRITOS, CA
Parts Used:
4890W1N005A
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Replace Inner Oven glass because it shattered
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.

Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.

Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)

Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.

Hope this helps
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from CARY, IL
Parts Used:
MEE36593201
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
No heat in oven mode
Verified P/N with LG. Took a few days . They sent names of several suppliers, cost was almost double. Ordered part from P/S, here in 2 days. Watched video on you tube. Unplugged, took off back, unplugged bake element, removed power box. The opening for bake element is still attached to rear panel by tiny bits of sheet metal. Used Dremel with cut-off wheel to cut thru nibs & deburr opening. this panel has to be removed, it rests on bottom panel & is held in position by power box. Removed bake element carefully, front of element broken, tried to put new element in, would not fit. Had to grind notches in bottom panel down to clear supports on new element. This did the trick. back together quick & no problems. If had to do again estimate less than 1 hour.. By the way am 81 yrs. young.
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from MILWAUKEE, WI
Parts Used:
5300W1R005A
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
wouldn't turn on
simply take picture b4 you start then replace same way.

WARNING!!! MAKE SURE YOU HAVE RIGHT PART!! They are very slow to return any type of credit
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
K R from BOISE, ID
Parts Used:
4778W1N001B
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Broken front leveler
This is a very simple repair of remove and replace. You do have to lay down the range to make it easy.
4 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from NORTH BEACH, MD
Parts Used:
6930W1A003X
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Thermostat needed to be replaced
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.
1 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LRE30755ST
1 - 5 of 5