Models
>
RA511*J4
RA511*J4 Hotpoint Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for RA511*J4
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
$11.33
If the drip bowls on your range or cooktop have become damaged, rusty, or are missing, they should be replaced. This is a genuine OEM replacement drip bowl that is chrome in color and 6 inches in diam...
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$8.44
This trim ring is an authentic OEM replacement part for your range. It serves as a decorative trim to the drip bowls found under the burner elements. The part will need to be replaced if it has become...
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$11.96
This 8-inch trim ring is a genuine OEM replacement part for your range. It sits around the surface burner elements for the style of ranges with low rise tilt lock burners. You may need to replace the ...
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$17.90
This 8-inch chrome drip bowl is a genuine OEM replacement part for your electric range. The drip bowl is designed to fit underneath the coiled burner elements, and is used to catch spills that result ...
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$51.36
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
This tilt lock hinge mounted surface element kit includes a 6 inch, two wire, 1350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$90.22
This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
$9.12
These are replacement screws designed to fit your range. They are made of metal and are approximately ¼ inch long. They come in a package of 12. These are OEM parts sourced directly from the manufacturer.
Special Order
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
In Stock
Order within the next 1 hr and 32 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for RA511*J4
Viewing 2 of 2Element will not heat
Fixed by these parts
How to fix it
Little to no heat when broiling
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Two 6" and two 8" burner elements needed replacing on a 36 year old counter range.
First of all I want to thank PartSelect. I have been looking for these parts for over 15 years. I am so happy to have found PartSelect. 1. Turn off Range 2. Turn off Breaker to the Range at your home Breaker Box. 3. Turn on Range to see if you turned off the right Breaker if so then turn Range off. 4. Lift Burner Element up. 5. Take off S
... Read more
ilver Trim Ring and Drip Bowl. 6. With screw driver unscrew the screw that is holding the Burner Element to the Range. It is located at the base of the hing where the Burner Element attaches to the Range. 7. Pull the Burner Element out just far enough to see the entire Element where the wires attach. 8. Snap off the two silver clips from each side of the White Glass Insulation Block with a screw driver. 9. With an adjustable wrench (crescent) loosen and remove the screws holding one of the wires to the Burner Element. 10. Find the same Terminal on the new Burner Element and reattach the wire to the new Burner Element Terminal. 11. Now do the same to the remaining Terminal. 12. Install the White Glass Insulation Block over the two Terminals and secure with the two silver clips. 13. Reattach Burner Element to Range with screw. 14. Replace Silver Trim Ring and Drip Bowl. 15. Turn on Breaker and test by turning on Range. You will smell a slight electrical burn smell for a moment while the new Elements heat for the first time. This will dissipate quickly. NOTE: I used the old White Glass Insulation Block I did not use the one that came with the new Burner Element. I found the old one to be the better choice. I saved the new one in case needed at a later date. The Job to replace both the 6" & 8" Burner Elements took less than 30 Minutes. I think it took longer to write this replacement instruction. LOL Very easy...Thanks again PartSelect. Charles McAllen, Texas
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Tampa, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace Drip Pans and Trim Rings for old stove
Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!
Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct ... Read more parts.
Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct ... Read more parts.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Bellevue, NE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Was this instruction helpful to you?
Thank you for voting!