Models
>
RCS-36
RCS-36 Garland Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This black front burner assembly is nine inches long. It is used with Maytag brand gas ranges.
In Stock
This toggle switch is also known as a fan switch. It has three positions: low, off, and high. This switch allows you to select the speed for the fan.
No Longer Available
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for RCS-36
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- T from Southfield, MI
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Toggle switch to operate exhaust fan and oven light inop.
First I turned off electrical power to the range by turning off the circuit breaker for the range.
Then I removed the two screws that hold the switch plate to top of front of range. Then I pushed the sw plate back toward to rear of range to disengage it from the guide pin, and lifted the switch plate and switch. Turned the switch p ... Read more late over and labelled the four wires to the switch. Removed the wire which were push-on. Which allowed me to remove the switch plate completely from the range. At my bench I used my Dremell with a cutting wheel to cut off the two push nuts/washers holding the switch to the switch plate. Removed the old switch and replaced it with the new one. Pushed to the new push nuts/washers provided in the kit, and re-assempled.
Then I removed the two screws that hold the switch plate to top of front of range. Then I pushed the sw plate back toward to rear of range to disengage it from the guide pin, and lifted the switch plate and switch. Turned the switch p ... Read more late over and labelled the four wires to the switch. Removed the wire which were push-on. Which allowed me to remove the switch plate completely from the range. At my bench I used my Dremell with a cutting wheel to cut off the two push nuts/washers holding the switch to the switch plate. Removed the old switch and replaced it with the new one. Pushed to the new push nuts/washers provided in the kit, and re-assempled.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Easton, MD
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch burned up; sparks and short in system
Took off plate over the rocker plate with screwdriver. Removed old switch. 2 posts were burned off!!! Plugged in new switch. Replaced panel over top. Worked great. Best $40 dollars ever spent. Saved me over $1000.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Westford, MA
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
fan/light switch broke
- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. oth ... Read more erwise, a piece of cake.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. oth ... Read more erwise, a piece of cake.
Read less
Was this instruction helpful to you?
Thank you for voting!