Models
>
NE58K9852WG
NE58K9852WG ((AA-0000)) Samsung Microwave Oven Combo
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
The convection fan motor spins the fan blade to circulate hot air through the oven for even heating.
In Stock
In Stock
In Stock
$501.91
This main top is for ranges. It provides a stable cooking surface and houses the surface cooking burners.
On Order
In Stock
In Stock
In Stock
In Stock
In Stock
$67.21
The oven door switch shuts the oven light off when you close the oven door.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for NE58K9852WG
Viewing 1 of 1Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Uwe from FORT COLLINS, CO
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shut off during self clean cycle and door stayed locked.
I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from SEABECK, WA
- Parts Used:
- DG96-00110F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Upper Oven convection Fan making bearing failure noises
First remove the internal fan guard, (two Philips Screws). Holding the fan blade and using a nut driver (10mm?) attempt to carefully remove the nut off of the shaft. If it loosens with a counterclockwise rotation, it is a Right Hand thread, Part#: PS11720788. If it loosens clockwise, it is Left Handed and is Part# PS11720787. When the co
... Read more
rrect fan arrives, check to make sure it matches, then continue with installation.
TURN THE POWER OFF
Following the door removal instructions in the Owners Manual, remove both upper and lower doors. Remove the screws that go into the cabinet on the sides, I believe there are (6). The bottom vent cover is also attached with the bottom screws, so you can remove that and set it aside.
Get some help to assist you with moving the stove out of the wall cavity, it's not heavy, but awkward. I used a small furniture cart, and the second time I used blocking on the cart to raise it to just below the oven and was able to easily slide out/in.
Rotate the oven so you can visualize the back. There are two panels on the back to remove, Starting with the bottom one, remove the screws, (a couple in the middle too) and slide the panel up, (Tabs into a notch on the top of each side of the panel) The second panel comes off the same way, there may be some screws on the side and top you need to be aware of. Once you open the back, the fan that needs to be replaced should be identical. If you have already removed the guard and fan blade from the inside compartment, it should be a simple swap out.
Put it back together in reverse order, put power back on and check to see if it worked. If so, slide it back into the cabinet, be careful the flex conduit is aligned so it doesn't interfere. Second time around it only took me about an hour total and I didn't need assistance.
Fan works, Oven quiet, Happy Wife, Happy Life.
TURN THE POWER OFF
Following the door removal instructions in the Owners Manual, remove both upper and lower doors. Remove the screws that go into the cabinet on the sides, I believe there are (6). The bottom vent cover is also attached with the bottom screws, so you can remove that and set it aside.
Get some help to assist you with moving the stove out of the wall cavity, it's not heavy, but awkward. I used a small furniture cart, and the second time I used blocking on the cart to raise it to just below the oven and was able to easily slide out/in.
Rotate the oven so you can visualize the back. There are two panels on the back to remove, Starting with the bottom one, remove the screws, (a couple in the middle too) and slide the panel up, (Tabs into a notch on the top of each side of the panel) The second panel comes off the same way, there may be some screws on the side and top you need to be aware of. Once you open the back, the fan that needs to be replaced should be identical. If you have already removed the guard and fan blade from the inside compartment, it should be a simple swap out.
Put it back together in reverse order, put power back on and check to see if it worked. If so, slide it back into the cabinet, be careful the flex conduit is aligned so it doesn't interfere. Second time around it only took me about an hour total and I didn't need assistance.
Fan works, Oven quiet, Happy Wife, Happy Life.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from WASHINGTON, DC
- Parts Used:
- DG94-00550A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Slider Assembly in Oven Warming Drawer
Install handled by building engineer...thankfully. Did not take long for him, however, to install both sides of the drawer.
Was this instruction helpful to you?
Thank you for voting!