PB195H42LT (425468) Poulan Lawn Tractor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Trace from LISLE, IL
- Parts Used:
- 532138971
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from DAMASCUS, OR
- Parts Used:
- 598559101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Mower belt fell off was cut by the drive pulley.
Got the proper length and pulley size belt via serial number. Checked the length prior to ordering to assure the length would be correct.
Took mower onto a flat surface where I could get on both sides of the deck. And then placed the belt on the back pulleys first . Then I routed it through the idler pulleys to the power pulley where I turned the pulley with putting finger pressure against the belt as I turned the pulley. And it went on with no problem . It is that simple just be sure to turn the pulley and apply the belt in the same direction at the same time.
Took mower onto a flat surface where I could get on both sides of the deck. And then placed the belt on the back pulleys first . Then I routed it through the idler pulleys to the power pulley where I turned the pulley with putting finger pressure against the belt as I turned the pulley. And it went on with no problem . It is that simple just be sure to turn the pulley and apply the belt in the same direction at the same time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hickory, NC
- Parts Used:
- 532177968
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Lound deck noise when mower put into motion
Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut came off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!