Models
>
20009
20009 (240000001-240999999 - 2004) Toro Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 20009
Viewing 10 of 10(2006)_WW_1.gif "Carburetor Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_3.gif "Engine Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_2.gif "Engine and Blade Assembly Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2007)_WW_5.gif "Front Axle and Wheel Assembly Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_6.gif "FWD Rear Axle and Low Wheel Assembly Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2007)_WW_6.gif "Handle Assembly Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2007)_WW_7.gif "Housing Assembly Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_4.gif "Page D Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_12.gif "Recoil Starter Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
(2004)_WW_11.gif "Rewind Starter Diagram and Parts List for 240000001-240999999 - 2004 Toro Lawn Mower")
Keep searches simple, eg. "belt" or "pump".
$24.90
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
In Stock
In Stock
In Stock
In Stock
$3.99
This is a nut, for a variety of outdoor lawn equipment. This part is a nylon insert locking nut, meaning it has a nylon collar insert that makes the nut resistant to turning from heavy vibrations. It ...
In Stock
$4.99
This is a genuine OEM replacement part sourced directly from the manufacturer. Spark plugs are important component of the ignition system, they take energy from the battery to create and electric spar...
In Stock
$4.99
This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It r...
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from FAIRVIEW, TN
- Parts Used:
- 650898A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Lost PartSelect Number PS9053486; Tecumseh 650898A screw
I lost two of the screws that hold the plastic Lawn Boy cowling to the Tecumseh lv195ea engine. I just replaced the lost screws with the newly ordered screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from YARDLEY, PA
- Parts Used:
- 105-1809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Was this instruction helpful to you?
Thank you for voting!