Models
>
YTH24K48
YTH24K48 ((96043033000)(2021-01)) Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for YTH24K48
Viewing 10 of 10
Keep searches simple, eg. "belt" or "pump".
$3.99
This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securi...
In Stock
Order within the next 12 hrs and your part ships today!
$6.21
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually...
In Stock
Order within the next 12 hrs and your part ships today!
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
$17.43
This is an OEM replacement part, sold individually.
The High Lift Blade is also referred to as a 2 in 1 blade. It throws the clippings better, and is used when you are just discharging or bagging t...
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
$48.56
This mandrel assembly is for lawn tractors.
Mandrel assembly attaches to the mower deck and spins the blades. The assembly may include multiple parts; refer to your parts diagram for a complete lis...
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
$14.93
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for YTH24K48
Viewing 2 of 2Drive system does not work
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WYTHEVILLE, VA
- Parts Used:
- 592855201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Husqvartna LGT-48DXL transmission drive belt was worn out
ALL VIDEOS and the official Husqvarna instructions will tell you that you MUST remove both the mowing deck and the entire clutch pulley assembly to switch the transmission drive belt. This is NOT true. It takes some effort and tight maneuvering, but this job can be done relatively quickly without removing either. You do NOT have to rem
... Read more
ove the mowing deck! You do NOT have to remove the clutch pulley assembly! What I did was to stand the tractor up nearly vertical, resting it against a golf cart I have and tying it in place for safety. Then, you have to loosen two black belt guides right by the clutch pulley assembly. I did NOT remove them, just left them hanging loose. Next, there is a silver bar that comes in from the outside of the mower chassis and attaches directly to the clutch, remove this entirely. Next, there is an electrical cord assembly in the way, trace this back, find where it plugs in, and unplug it. Next, in order to be able to slide the belt fully over the clutch pulley assembly, you have to take the mower deck belt off of JUST THE ONE spindle closest. I tie wrapped it in place after getting it off the spindle so that I could easily put it back onto the spindle as the last step when done. Once the mowing deck belt is off the closest spindle, you can then slide the drive belt completely over the clutch pulley assembly. You can then easily remove the entire drive belt, taking note (I took pictures) of how it is routed. Then, just reverse all of this. I began by fitting the drive belt over the clutch pulley assembly to make sure that end was correct. I then put the previously mentioned two guides, silver bar, and electrical cord back in place. Next, I shoved the belt down where it goes, working it down towards the transmission and routing it correctly. Of course, it is a little difficult with the limited space available, but I would rather do that then needlessly take the entire mowing deck off. You finally have to CAREFULLY slide it over the PLASTIC fan blades on the transmission. Once past those, it slides easily in place. The last step is to put the mowing deck belt that you previously removed and tie wrapped in place back onto the spindle. That's it! Only takes about 30-45 min. done this way.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!