Models
>
502130
502130 ((2015-12)) Husqvarna Lawn Mower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$3.99
This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securi...
In Stock
$6.21
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually...
In Stock
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
In Stock
$14.93
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
On Order
In Stock
This is an OEM bowtie cotter pin for lawn tractors. It is sold individually. This part is made of metal material, so over time, this metal can corrode or rust, especially if the lawn tractor is expose...
In Stock
$13.69
This is a flat idler pulley, approved by the manufacturer for use in lawn tractors. The pulley provides tension to the belt. For this DIY repair you will need a wrench and pliers. You will start by re...
On Order
$26.14
This blade idler pulley (part number 196106) is for lawn tractors.
Blade idler pulley 196106 applies tension to the blade belt, allowing the belt to turn.
In Stock
This ground drive fixed idler pulley is for lawn tractors.
910 inch offset
Ground drive fixed idler pulley helps apply tension to the drive belt, allowing the belt to turn.
Wear work gloves to...
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 502130
Viewing 2 of 2Drive system does not work
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynn from BOILING SPGS, PA
- Parts Used:
- 532130969
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Drive belt came off from transaxle pulley, noticed in bad shape, ordered new one form parts select.
The drive belt literally goes from the back of the tractor to the front. The mower must be removed, helps to have the tractor up on blocks to give adequate room for work on underside. Belt goes easiest on the engine first, then thread to the rear, install on the rear, (driven pulley) then on the idlers. Check to assure that it function
... Read more
s properly before re-installing the mower. If you have the owners manual, there is a diagram, (check your orientation, it is not clear if it is a birdseye or under tractor view) which offered some help. When replacing belt, check the transaxle front mount, mine was broken which is why the belt came off in the first place. Repairing the mount was quite a job in itself, but now works fine.
Read less
Was this instruction helpful to you?
Thank you for voting!
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!