Models
>
JT051CAE1612
JT051CAE1612 Whirlpool Ice Maker
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JT051CAE1612
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
In Stock
$13.13
This is a compression nut for your refrigerator/freezer. The compression nut is used with the plastic water line for the icemaker assembly. It is the connection between the water supply line and the o...
In Stock
In Stock
This single outlet water valve is intended for use with some commercial ice machines, and not refrigerator icemakers. It comes with a mounting bracket, two screws, and a washer.
No Longer Available
Special Order
$364.18
This part helps circulate water through the evaporator to form ice that will be cut into cubes.
In Stock
This is a high temperature adhesive that is used for gaskets and felt seals.
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JT051CAE1612
Viewing 2 of 2Leaking
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NICOLAS from MCALLEN, TX
- Parts Used:
- WP756782
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
The water pump broke (too old).
I removed the three nuts that hold the old pump, easy. Next step was to replace with the new pump, tricky, because it goes real deep in the machine and my arms barely reach it.
After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake.
What I liked most, is that you don't need to do any ... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump.
What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!!
Last night I fixed it, and today I'm enjoying again fresh ice.
One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice!
Thanks a lot PartSelect !!!
After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake.
What I liked most, is that you don't need to do any ... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump.
What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!!
Last night I fixed it, and today I'm enjoying again fresh ice.
One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice!
Thanks a lot PartSelect !!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Flower Mound, TX
- Parts Used:
- 759296
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Quit making ice
This is a stand alone ice maker that uses a standard water valve. When the valve fails (usually stuck open) the water never chills enough to freeze because water is constantly flowing into the hopper. The valve is in the very front. Remove the front panel. Turn of the water supply and disconnect the valve. Replace the valve and turn on th
... Read more
e water. Let the machine run through 1 cycle before the new valve will dispense water. Done.
Read less
Was this instruction helpful to you?
Thank you for voting!