Models
>
DGHD2361TF0
DGHD2361TF0 Frigidaire
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for DGHD2361TF0
Viewing 11 of 11
Manuals & Guides for DGHD2361TF0
Click to downloadInstall
Installation Instructions
(0.87MB)
Manual
Owner's Manuals
(7.01MB)
Specs
Product Specifications Sheet
(0.56MB)
Wiring
Wiring Diagram
(0.56MB)
Keep searches simple, eg. "belt" or "pump".
The water filter in your refrigerator should be replaced every six months in order to provide clean, fresh tasting water. The filter absorbs impurities in the water like heavy metals, pesticides, and ...
In Stock
$20.28
This charcoal air filter is a genuine OEM replacement part for your refrigerator. The charcoal filter absorbs food odors, which in turn helps to ensure your ice tastes better. Ice tends to absorb smel...
In Stock
$106.78
This is a genuine Frigidaire part for your refrigerator. This is an ice maker, which connects to the water lines to provide fresh ice. The most common reason to replace this part is if your refrigerat...
In Stock
$21.58
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer do...
In Stock
In Stock
$126.32
Crisper cover with glass works with some Frigidaire, Electrolux, White Westinghouse, and Tappan models of fridges.
This is a genuine OEM part that works for some models of Frigidaire, Electrolux, W...
On Order
In Stock
In Stock
In Stock
In Stock
This door gasket is for the freezer door on the refrigerator. The gasket is grey in color. This part is approximately 34-1/2" wide x 24" long. The door gasket is on the inner door panel and creates a ...
In Stock
This is an adjustable foot for your freezer, refrigerator, and dryer. This part supports your unit by screwing into one of the bottom four corners, and adjusting the height of your machine. If your ap...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for DGHD2361TF0
Viewing 13 of 13Ice maker not making ice
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Door Sweating
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Frost buildup
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- robert from sioux falls, SD
- Parts Used:
- 241675704
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker wouldn't change from crushed to cubed ice
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There i
... Read more
s 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from N CALDWELL, NJ
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not working
Simple three steps... 1) There's an front section to the ice-maker to take off. One Phillips screw is on the side, one screw is underneath near the inside of the refrigerator wall. Just unscrew and store. 2) There's a small plastic unit just inside the ice maker to take out. It's held in by a small nut that requires about a 4" extension
... Read more
to reach. (You may be able to unscrew the nut with small needle-nose pliers). Just unscrew and take out the unit - the unit functions just to keep the ice maker wiring in place. 3) The wiring looks a mess, but there's just one wiring connector to the ice maker assembly. Unsnap it. The ice maker is not screwed in, it just slides in -- reach in and pull the assembly straight out; when it stops, lower it a bit and it will come free. Reverse the instructions to install the new unit.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from AMARILLO, TX
- Parts Used:
- 240597203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used
... Read more
my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Read less
Was this instruction helpful to you?
Thank you for voting!