Models
>
KUDD01DSSS0
KUDD01DSSS0 KitchenAid Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KUDD01DSSS0
Viewing 6 of 6
Manuals & Guides for KUDD01DSSS0
Click to downloadInstall
Installation Instructions
(1.73MB)
Install
Installation Instructions
(2.09MB)
Manual
Owner's Manuals
(2.42MB)
Manual
Owner's Manuals
(5.01MB)
Manual
Owner's Manuals
(5.01MB)
Keep searches simple, eg. "belt" or "pump".
$194.29
This part moves water through the spray arm by rotating inside the pump.
In Stock
Order within the next 11 hrs and your part ships today!
$328.32
This part delivers water to the spray arms to aid in cleaning the dishes.
In Stock
Order within the next 11 hrs and your part ships today!
Special Order
Located at the bottom of the dishwasher, this filter keep large particles of food and foreign objects away from the pump.
No Longer Available
This water inlet valve has attaching solenoids on the valve that open and close according to the desired amount of water needed.
No Longer Available
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KUDD01DSSS0
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from Spokane, WA
- Parts Used:
- WP8194092
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The dishwasher started making a lot of noise during certain parts of the wash cycle.
A Kitchenaid repairman came to look at the dishwasher and found that the rotor needed to be replaced but none were in stock. The part was on backorder and the price would be $75 plus a $55 installation fee.
I went online and found the exact same part at PartSelect for $37.98 plus shipping and when it arrived, replaced the defe ... Read more ctive rotor easily. Now the dishwasher is whisper quiet like it was when new. I saved a little over $80 by ordering from PartSelect and replacing it myself.
I went online and found the exact same part at PartSelect for $37.98 plus shipping and when it arrived, replaced the defe ... Read more ctive rotor easily. Now the dishwasher is whisper quiet like it was when new. I saved a little over $80 by ordering from PartSelect and replacing it myself.
Read less
Was this instruction helpful to you?
Thank you for voting!
Upper drawar of dual drawar dishwasher stopped filling. Incorrectly assumed fill valve had failed and replaced. Problem turned out to be another component. Replacing valve was part of process of elemination to figure out what was wrong.
Dishwasher fill valve is in on bottom of diswher.
Dual drawar dishwasher has doubble solenoid valve for fill. Lower drawer is pulled off and turned sideways to gain access. Access is still tight. Good news is that I bought two new hose clamps. Best way to remove old hose clamps is to saw through part of clamp mechanism. Inlet li ... Read more ne hooks up with a union-type connection that contains a seal that looks like a garden hose washer. Sawing through solenoid valve discharge line(s) hose clamps allows valve removal without damaging valve discharge hoses. Large person may have difficulty doing repair if lower drawer can not be slid to right after pulling it out. Other annoyance is that new valve did not come with new inlet line seal. I used the old seal sucessfully. Hardest part was getting old clamps off and getting fill line connection back on. Easy to cross-thread fill line connection to fill valve. Also easy to damage fill line if there is not much space between back of dishwasher and wall. I ended up making a metal fill line using a 3/8 NPT brass pipe union that had the same threads as on the fill valve inlet. Half of union is thrown away and the remaining half is filed flat. This allowed using an elbow to turn the fill line 90 degrees as it come through the back of the dishwasher. Back of dishwasher is only 2 inches from back of wall.
Dual drawar dishwasher has doubble solenoid valve for fill. Lower drawer is pulled off and turned sideways to gain access. Access is still tight. Good news is that I bought two new hose clamps. Best way to remove old hose clamps is to saw through part of clamp mechanism. Inlet li ... Read more ne hooks up with a union-type connection that contains a seal that looks like a garden hose washer. Sawing through solenoid valve discharge line(s) hose clamps allows valve removal without damaging valve discharge hoses. Large person may have difficulty doing repair if lower drawer can not be slid to right after pulling it out. Other annoyance is that new valve did not come with new inlet line seal. I used the old seal sucessfully. Hardest part was getting old clamps off and getting fill line connection back on. Easy to cross-thread fill line connection to fill valve. Also easy to damage fill line if there is not much space between back of dishwasher and wall. I ended up making a metal fill line using a 3/8 NPT brass pipe union that had the same threads as on the fill valve inlet. Half of union is thrown away and the remaining half is filed flat. This allowed using an elbow to turn the fill line 90 degrees as it come through the back of the dishwasher. Back of dishwasher is only 2 inches from back of wall.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Melbourne, FL
- Parts Used:
- 8194425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
E2 F2 error code
IF PartSelect had sent the part I ordered all might have worked. I paid the shipping for my needed part. The wrong part was returned at my expense also. You cost me $16. and I got nothing but poor service.
Was this instruction helpful to you?
Thank you for voting!