Models
>
HDA100S-45AW
HDA100S-45AW Hotpoint Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HDA100S-45AW
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$12.63
The rack slide end cap attaches to the rails of the upper dishrack, to prevent it from sliding all the way out. It is a one-inch white plastic part that can break over time. This might be the part you...
In Stock
If the upper rack in your dishwasher is not sliding in and out properly, the rollers may need to be replaced. Faulty rollers can also cause your rack to fall off the track, the door may not close prop...
In Stock
The corner tub baffle is made of black plastic, and is used to prevent water from leaking out of the dishwasher while it is operating. This genuine OEM part is for the lower right-hand side of your di...
In Stock
This is a genuine OEM corner tub baffle for the lower left-hand side of your dishwasher. It is made of black plastic, and is used to prevent water from leaking out of the dishwasher while it is operat...
In Stock
In Stock
$25.96
This part is sold individually. It is recommended that both sides are changed when replacing one.
In Stock
$13.83
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
In Stock
$27.45
This interlock switch is a genuine OEM part that can be used in a variety of appliances like dishwashers and dryers. The switch is also known as a belt switch and works as a simple on and off mechanis...
In Stock
In Stock
$249.86
This pump and motor kit replaces many old style pump and motor kits that were manufactured since 1970. The instructions are included with this kit to help you to make it adaptable to your dishwasher.
...
In Stock
$106.19
This dishwasher door gasket is compatible with those models having a two ear housing and a square spacer. It's gray and it creates a water tight seal around your dishwasher's door.
In Stock
$57.50
This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or ...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for HDA100S-45AW
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Fairfield, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece the
... Read more
n slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
guides.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Columbus, OH
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken upper rack roller, rack kept falling off the track
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Morgan Hill, CA
- Parts Used:
- WD26X10013, WD24X10014, WD21X802, WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Water not draining from dishwasher
I had never done work on my dishwasher - I was a rookie in this area. Turns out the work itself was quite simple. Pulled the dishwasher out, turned it over, and was able to easily replace the motor and pump assembly. The drain tube was also an easy replace. A couple key notes:
1. I also purchased a new drain solenoid and impell ... Read more er kit. Note that both of these items are already included in the Motor and Pump kit replacement. There is no need to by both, now I have extras.
2. The end of the drain tube has to be trimmed if you are routing the drain tube to an air gap mounted on your kitchen sink. You have to cut the large diameter end of the tube to get to the narrow portion that will fit on your air gap.
3. The first cycle you run with the new motor/pump assembly is noisy. When you first fire it up the components in the pump are all dry, and they squeal until the water gets to them. I initially thought I had done something wrong, but once the water started flowing all the peculiar sounds cleared up.
1. I also purchased a new drain solenoid and impell ... Read more er kit. Note that both of these items are already included in the Motor and Pump kit replacement. There is no need to by both, now I have extras.
2. The end of the drain tube has to be trimmed if you are routing the drain tube to an air gap mounted on your kitchen sink. You have to cut the large diameter end of the tube to get to the narrow portion that will fit on your air gap.
3. The first cycle you run with the new motor/pump assembly is noisy. When you first fire it up the components in the pump are all dry, and they squeal until the water gets to them. I initially thought I had done something wrong, but once the water started flowing all the peculiar sounds cleared up.
Read less
Was this instruction helpful to you?
Thank you for voting!