Models > DU45A-1

DU45A-1 Admiral Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DU45A-1

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
$20.77
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
Sold individually.
Special Order
This screw is well under an inch long, and is made of metal.
In Stock
$9.12
This screw is sold individually. Size: 8-32 x 1/4 inch.
Special Order
$1.55
Special Order
Sold Individually. Suggested to replace both at the same time.
No Longer Available
This assembly includes the 2 wheels and bracket.
No Longer Available
This pump motor shaft seal will help prevent the water inside the dishwasher from leaking around the shaft of the motor.
Special Order
$6.60
Special Order
Special Order
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DU45A-1

Viewing 2 of 2
Leaking
Fixed by these parts
Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from Tryon, NC
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
77 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from Holly, MI
Parts Used:
154106202, 5300806833
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Water leaking from under dishwasher
Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from New Orleans, LA
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Water leak underneath dishwasher
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!