Models
>
JGP326WEV4WW
JGP326WEV4WW General Electric Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGP326WEV4WW
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
$43.11
This part sits on top of the valve. Once the knob is turned it will create a spark that will light the gas and start the burner.
In Stock
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
$54.42
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
In Stock
Sold Individually. Order quantity needed.
No Longer Available
$9.12
These are replacement screws designed to fit your range. They are made of metal and are approximately ¼ inch long. They come in a package of 12. These are OEM parts sourced directly from the manufacturer.
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGP326WEV4WW
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Little to no heat when baking
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Logansport, IN
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. Ther
... Read more
e are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bloomsbury, NJ
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Tulsa, OK
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electronic ignitors would not stop firing even when burner was off
first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.
Was this instruction helpful to you?
Thank you for voting!