KHMS2050SSS0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Agua Dulce, CA
- Parts Used:
- 8205992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray broke
There was no "fixing" per say but we still could not use the microwave without the plate. This has to be one of the biggest plates for a microwave. We ordered this through your company and we had it three days later. THREE DAYS! We had expected anywhere from 1-2 weeks. My husband was so impressed he bookmarked your site for future reference. Thank you for being so efficient and prompt. The glass turntable fit like a glove! Sincerely, Mark and Lia Hammond
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Papkin from Glendale, CA
- Parts Used:
- W10120839A, 8204670
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Surface lights and filters needed replacement
By pulling the filter screens units down and out with a pair of pliers I had access to the surface lights. Pulled the lights out of their sockets and replaced the bulbs. Real easy. Since the filter units were out, replaced the filters and reinstalled the filter units. The whole operation took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- duane from san diego, CA
- Parts Used:
- W11661547, W10120840A, 8206222, 8205994
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Fire in microwave melted several parts
Remove the filters and use a Torx driver to remove two screws holding the motor. The wires on on the motor are held in place by a plastic clamp that must be pried open on one side. That's all it takes to replace the drive motor. Everything else that makes the turntable spin lifts off from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DECATUR, GA
- Parts Used:
- W11707984
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave wouldn't turn on and found breaker been tripped and then microwave wouldn't turn on at all.
Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyler from PARKVILLE, MD
- Parts Used:
- W10269458
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Door close wasnt registering and the microwave wouldn't turn on.
I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- getachew from aldie, VA
- Parts Used:
- W10315274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
sparks when turned on
replace one of the four rack supports which was melting
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E G from SILVERDALE, WA
- Parts Used:
- W10211972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The display kept asking me to close the door, even though the door was closed. The interior light stayed on.
I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PASADENA, MD
- Parts Used:
- WP8206635
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Key board no touch and beeps
Unplugged unit 30 minutes before disassemble. Removed screws from door on Handle side had to remove door to get the three screws out on hinges, pop inner liner to remove key board pulled ribbon cable installed new board replaced inner panels , hung door and tested . Worked for couple hours same problems. Loss of key board and beeps next ?
Was this instruction helpful to you?
Thank you for voting!
Turntable driver broke/glass turntable broken
Dropped in the driver. Lined up the glass turntable to the driver. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CLERMONT, FL
- Parts Used:
- W10120840A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Sensors acting strange
Replace two filters underneath the microwave.
No tools requires
Repair took 15 seconds
No tools requires
Repair took 15 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeport, IL
- Parts Used:
- W10120840A, W10120839A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filters needed replacing.
Pulled filter holders out, removed filters, washed holders, installed new filters, and reinstalled assemblies.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robertt from MOUNT JULIET, TN
- Parts Used:
- W10120840A, W10120839A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
REPLACE OLD FILTERS-2 Sets
Requires 2 sets of replacement parts. Prior filters included a charcoal filter sandwiched between 2 aluminum filters/screens (3 total parts per side). Replacement charcoal filter was already attached to an aluminum screen so just needed to add 1 aluminum screen/filter so the charcoal was again sandwiched between the 2.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from MOUNT ULLA, NC
- Parts Used:
- W10269458
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The close door warning kept coming on and the microwave would not run
Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from PALMYRA, VA
- Parts Used:
- W10315274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Supports were bad
Replaced the supports and rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from TUMWATER, WA
- Parts Used:
- 8206504
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced door handle with worn off silver finish.
Unscrewed 3 screws on side of door and two on the bottom. Slowly pry apart outside frame from black inside facing door. Separate pieces carefully. You won’t have to completely remove outside door cover if you have a short driver for the two Torx screws holding the handle on. Replace and carefully put back together. Tip: do not overscrew the screws, back in, it will easily crack the old plastic.
Was this instruction helpful to you?
Thank you for voting!