OEM Black and Decker Miter Saw Parts & Accessories

Brush and Spring

$8.86

Fix Number: FIX10166057
Manufacturer Part Number: 145323-06

This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.

Watch the install video

Blade Adapter Ring

$4.99

★★★★★

2 Reviews

Fix Number: FIX10166690
Manufacturer Part Number: 152636-00

This is an authentic adapter ring used to mount the saw blade to your miter saw. It is sold as an individual part. Standard 12-inch saw blades have a 1-inch arbor hole, while most miter saw arbors are 5/8 of an inch. This adapter ring is placed on the blade hole and over the arbor so you can use a 12-inch blade. This part is prone to wear and tear, which will make the blade unbalanced, signalling that it should get replaced.

Watch the install video

Kerf Plate

$11.49

Fix Number: FIX10166116
Manufacturer Part Number: 146726-02

This Kerf plate is a genuine DeWalt replacement part. It is made of plastic with a slot in the middle for the saw blade to slide through. It has 3 screw holes on each side (6 in total) to firmly secure the kerf plate to your saw. rnrnKerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf plate for your tool can give a rough edge to the material you’re cutting.

Watch the install video

Ball Bearing

$5.26

Fix Number: FIX10180911
Manufacturer Part Number: 605040-27

This part includes one OEM ball bearing. This ball bearing is sealed on both sides. They are designed to minimize friction between moving parts and evenly distribute weight. Bearings are a general wear part that require regular maintenance to keep your equipment running smoothly and efficiently.

Terminal

$3.99

Fix Number: FIX10185238
Manufacturer Part Number: 88667-00

Watch the install video

Outer Clamp

$9.61

Fix Number: FIX10166601
Manufacturer Part Number: 151962-01

This is an outer clamp for a miter saw and it is sold individually. It works with another flange (sold separately), to secure the saw blade. The shape of the outer clamp is identical to that of the saw arbor. This stops the flange from moving on the arbor shaft. It is common for the blade flanges to wear over the use of the saw, and this can lead to a wobbly blade. Start your repair by unplugging the tool. Pull the guard to expose the blade screw. Use the wrench that came with the purchase of the saw and remove the outer clamp. The new outer clamp can now be installed in its place.

Watch the install video

Switch Kit

$68.09

★★★★★

1 Review

Fix Number: FIX10178151
Manufacturer Part Number: 5140112-17

This is a genuine OEM replacement part. Sold individually. This kit was made to replace the old switch on the Miter Saws that was discontinued. It includes both handle halves, handle to carry saw, new switch, screws and wire terminals. It also includes an installation sheet. Flat head screwdriver is needed for repair. This switch is a common replacement part and is compatible with the Miter Saw models listed below.

Installation Instructions

Rick from FERNLEY, NV

I had no problems

the installation was simple the instructions were right on the money. Read more...

Miter Saw Clamshell Set

$43.98

Fix Number: FIX10170218
Manufacturer Part Number: 380452-00

This clamshell housing set is sourced right from the original manufacturer. It is made of a durable plastic and is yellow in color. Please note that this is the handle housing only and includes both sides. The mounting/assembly hardware and trigger switch are not included and are sold separately. The handle housing is a common replacement part for miter saws and should be replaced if it has cracked or bent.

Cord Protector

$5.55

★★★★★

3 Reviews

Fix Number: FIX10173396
Manufacturer Part Number: 445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Watch the install video

Locking Pin

$5.19

Fix Number: FIX10170809
Manufacturer Part Number: 387130-00

This part includes one locking pin for a miter saw. This is an OEM certified part, meaning it is a guaranteed fit. The locking pin is responsible for locking the saw arm in the down position. The locking pin moves in and out of the bracket, which is how it locks and unlocks the head. You will also want to inspect the condition of the O-ring on the locking pin just in case it also needs to be replaced. The O-ring will need to be purchased separately, as it is not included with the locking pin. If it is still in good condition, just simply transfer the old one to the new locking pin.

Black and Decker Miter Saw Parts

Popular Black and Decker Miter Saw Parts

Installation Instructions

Appliance Type

Popular Black and Decker Miter Saw Models

Black and Decker Miter Saw Parts

Start With Your Model Number

Popular Black and Decker Miter Saw Parts

Installation Instructions

Appliance Type

Popular Black and Decker Miter Saw Models